- 您現在的位置：買賣IC網 > PDF目錄297426 > SPX2940U3-L-3.3 3.3 V FIXED POSITIVE LDO REGULATOR, PSFM3 PDF資料下載
參數資料
| 型號： | SPX2940U3-L-3.3 |
| 元件分類： | 固定正電壓?jiǎn)温份敵鯨DO穩壓器 |
| 英文描述： | 3.3 V FIXED POSITIVE LDO REGULATOR, PSFM3 |
| 封裝： | TO-220, 3 PIN |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 165K |
| 代理商： | SPX2940U3-L-3.3 |
Rev. 10/24/00
SPX2940
APPLICATION HINTS
External Capacitors
A minimum capacitance of 22
F and conditions on ESR (Equivalent Series Resistance) must be met. The minimum value for the capacitance is
22
F and can be increased without limit. However the ESR may cause loop instability if it is too high or too low. The following graph shows the
acceptable range for the ESR.
If the capacitor does not meet these requirements oscillation can result.
ESR is specified only at room temperature. Therefore the designer must ensure the proper behavior of the ESR over the temperature range. ESR, for
electrolytic capacitor, will increase by about 30X as the temperature is reduced from 25
°C to -40°C. Aluminum electrolytic capacitors are not well
suited for low temperature operation.
Solid tantalum capacitors’ ESR are more stable over temperature, but expensive. A cost-effective approach is then to put in parallel a solid tantalum
and a aluminum electrolytic capacitors in the ratio25/75%.
Thermal Consideration
Although the SPX2940 offers some limiting circuitry for overload conditions, it is necessary not to exceed the maximum junction temperature, and
therefore to be careful about thermal resistance. The heat flow will follow the lowest resistance path, which is the Junction-to-case thermal
resistance. In order to insure the best
thermal flow of the component, a proper mounting is required. Note that the case of the device is electrically connected to the output. In case the
case has to be electrically isolated, a thermally conductive spacer can be used. However do not forget to consider its contribution to thermal
resistance.
Formulas for calculating the power dissipated in the regulator are the following:
IIN = IL + IG
PD = (VIN + VOUT) * IL + VIN * IG
Where IIN is the input current, IL is the load current, IG is the ground current, PD is the power dissipated, VIN is the input voltage and VOUT is the
output voltage.
Output Capacitor ESR
OUTPUT CURRENT (mA)
EQUIVALENT
SERIES
RESISTANCE
(
)
1000
800
600
400
0
200
0.01
0.1
1
10
100
C
OUT = 22 F
V
O = 5V
STABLE
REGION
相關PDF資料 |
PDF描述 |
|---|---|
| SPX2940U3-L-5.0 | 5 V FIXED POSITIVE LDO REGULATOR, 1 V DROPOUT, PSFM3 |
| SPX2951CS-L-3.0 | FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO8 |
| SPX4040B3M-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO3 |
| SQ24S05018-PS0S | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| SQ24S05060-PS00G | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SPX2940U-5.0 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:1A Low Dropout Voltage Regulator Fixed Output, Fast Response |
| SPX2940U-L-2-5 | 功能描述:低壓差穩壓器 - LDO 1.0A LW DROPOUT VLT 1.5A PEAK OUTPT CURR RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| SPX2940U-L-3-3 | 功能描述:低壓差穩壓器 - LDO 1.0A LW DROPOUT VLT 1.5A PEAK OUTPT CURR RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| SPX2940U-L-5-0 | 功能描述:低壓差穩壓器 - LDO 1.0A LW DROPOUT VLT 1.5A PEAK OUTPT CURR RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| SPX2941 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:1A Low Dropout Voltage Regulator, Adjustable Output, Fast Response |
發布緊急采購，3分鐘左右您將得到回復。