- 您現在的位置：買賣IC網 > PDF目錄372201 > SP9601AS 12-Bit, Low Power Voltage Output D/A Converter PDF資料下載
參數資料
| 型號： | SP9601AS |
| 英文描述： | 12-Bit, Low Power Voltage Output D/A Converter |
| 中文描述： | 12位，低功耗，電壓輸出D / A轉換 |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 160K |
| 代理商： | SP9601AS |
SP9601DS/02
SP9601 12-Bit, Low-Power Voltage Output
5
Copyright 2000 Sipex Corporation
V
OUT
V
REF
DAC
16
7
9
3 TO 7
DECODE
3
9
LATCH
12
1
SHIFT
REGISTER
D
IN
–
+
Figure 1. Detailed Block Diagram
The operational amplifier is a rail-to-rail input,
rail-to-rail output CMOS amplifier. It is capable
of supplying 5mA of load current in the
±
3 volt
output range. The initial offset voltage is laser-
trimmed to improve accuracy. Settling time is
30
μ
s for a full scale output transition to 0.024%
accuracy.
The bipolar voltage output of the
SP9601
is
created on chip from the DAC output voltage
(V
) by using an operational amplifier and
two feedback resistors connected as shown in
Figure 2. This configuration produces a
±
4.5V
bipolar output range with standard offset binary
coding,
Table 1
.
USING THE SP9601
External Reference
The DAC input resistance is code dependent
and is minimum at code 1877 and nearly infinite
at code 0. Because of the code-dependent nature
of the reference a high quality, low output im-
pedance amplifier should be used to drive the
V
REF
input.
Serial Clock and Update Rate
The
SP9601
maximum serial clock rate (SCLK)
is given by 1/(t
CH
+t
CL
) which is approximately
12.5 MHz. The digital word update rate is lim-
ited by the chip select period, which is 12 X
SCLK periods plus the CS high pulse width t
.
This is equal to a 1
μ
s or 1 MHz update rate.
However, the DAC settling time to 12–Bits is 30
μ
s, which for full scale output transitions would
limit the update rate to 33 kHz.
Logic Interface
The
SP9601
is designed to be compatible with
TTL and CMOS logic levels. However, driving
the digital inputs with TTL level signals will
increase the power consumption of the part by
300
μ
A. In order to achieve the lowest power
consumption use rail-to-rail CMOS levels to
drive the digital inputs.
Midscale Preset
By holding CS pin low during Power-up, the
DAC output can be forced to 0V. Following
Power-up, the CS pin should be kept low as the
first digital word is shifted into the shift register.
When CS pin is set high, the digital word in the
shift register (loaded by the last 12 clock cycles)
is latched into the DAC register. Thus, the DAC
can be forced to go from midscale (1000 0000
0000, on Power-up) to any digital state, without
entering an unknown state.
–
+
D
IN
V
REF
V
OUT
V
DAC
V
OUT
V
DAC
D
IN
2048
x V
REF
D
IN
4096
WHERE
=
=
x V
REF
– 1
)
(
(
)
Figure 2. Transfer Function
DAC
REGISTER
40K
40K
相關PDF資料 |
PDF描述 |
|---|---|
| SP9601BN | 12-Bit, Low Power Voltage Output D/A Converter |
| SP9601BS | 12-Bit, Low Power Voltage Output D/A Converter |
| SP9601JS | 12-Bit, Low Power Voltage Output D/A Converter |
| SP9601KN | 12-Bit, Low Power Voltage Output D/A Converter |
| SP9601KS | 12-Bit, Low Power Voltage Output D/A Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP9601BN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:12-Bit, Low Power Voltage Output D/A Converter |
| SP9601BS | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:12-Bit, Low Power Voltage Output D/A Converter |
| SP9601JN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:12-Bit, Low Power Voltage Output D/A Converter |
| SP9601JS | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:12-Bit, Low Power Voltage Output D/A Converter |
| SP9601KN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:12-Bit, Low Power Voltage Output D/A Converter |
發布緊急采購，3分鐘左右您將得到回復。