- 您現在的位置：買賣IC網 > PDF目錄372201 > SP9504JP Quad, 12-Bit, Voltage Output D/A Converter PDF資料下載
參數資料
| 型號： | SP9504JP |
| 英文描述： | Quad, 12-Bit, Voltage Output D/A Converter |
| 中文描述： | 四，12位電壓輸出D / A轉換 |
| 文件頁數： | 7/11頁 |
| 文件大小： | 184K |
| 代理商： | SP9504JP |
SP9504DS/03
SP9504 Quad, 12-Bit, Voltage Output D/A Converter
7
Copyright 2000 Sipex Corporation
bringing WR1 low will transfer the data to the
addressed DAC. The user should be sure to
bring WR1 high again so that the next selected
DAC will not be overwritten by the last digital
code. This mode of operation may be useful in
applications where preloading of the input
registers is not necessary
Figure 3a
.
A fully transparent mode is realized by tying
WR1, CS, WR2, and XFER all low. In this
mode, anything that is written on the12-bit data
bus will be passed directly to the selected DAC.
Since both latches are not being used, the previ-
ous digital word will be overwritten by the new
data as soon as the address changes. This may be
useful should the user want to calibrate a circuit,
by taking full scale or zero scale readings for all
four DAC’s,
Figure 3b
.
ZEROING DAC OUTPUTS
While keeping XFER pin high, the DAC outputs
can be set to zero volts two different ways. The
first involves the CLR and WR2 pins. In normal
operation, the CLR pin is tied high, thus, dis-
abling the clear function. By cycling WR2 and
CLR through "1" —"0" —"1" sequence, a digi-
tal code of 1000 0000 0000 is written to all four
DAC registers, producing a half scale output or
zero volts. The second utilizes the built in power-
TRANSFERRING DATA
To transfer the four 12-bit words in the four
input registers to the four DAC registers:
1) Set CLR=1, CS=1, WR1=1.
2) Cycle WR2 and XFER through the “1”
— “0” — “1” sequence.
To set the outputs of the four DAC’s to 0V, cycle
WR2 and CLR through the “1” — “0” — “1”
sequence, while keeping XFER=1.
ONE LATCH, OR NO LATCHES
The latches that form the registers can be used in
a “semi-” transparent mode, and a “fully-”
transparent mode. In order to use the
SP9504
in
either mode the user must be interfaced to a
12-bit bus only (B1=1).
The semi–transparent mode is set up such that
the second set of latches is transparent and the
first set is used to latch the incoming data. Data
is latched into the first set rather than the second
set, in order to minimize glitch energy induced
from the data formatting. In this mode, XFER,
WR2 and CS are tied low, and WR1 is used to
strobe the data to the addressed DAC. Each
DAC is addressed using the address lines A
and
A
. After the appropriate DAC has been selected
and the data is settled at the digital inputs,
Figure 2. Transfer Function
REF IN
–
+
V
Out
D
V
Out
=
D
( )
V
DAC
=
x
D
4,096
V
DAC
REF IN
REF IN
相關PDF資料 |
PDF描述 |
|---|---|
| SP9504 | Quad, 12-Bit, Voltage Output D/A Converter |
| SP9504JS | Quad, 12-Bit, Voltage Output D/A Converter |
| SP9504KP | Quad, 12-Bit, Voltage Output D/A Converter |
| SP9504KS | Quad, 12-Bit, Voltage Output D/A Converter |
| SP9600BN | 12-Bit, Low Power Voltage Output D/A Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP9504JS | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Quad, 12-Bit, Voltage Output D/A Converter |
| SP9504KP | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Quad, 12-Bit, Voltage Output D/A Converter |
| SP9504KS | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Quad, 12-Bit, Voltage Output D/A Converter |
| SP959B | 制造商:SIPAT 制造商全稱:SIPAT 功能描述:DECT RF Filters |
| SP959B01-TD01 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:China Electronics Technology Group Corporation No.26 Research Institute |
發布緊急采購，3分鐘左右您將得到回復。