- 您現在的位置：買賣IC網 > PDF目錄385855 > SP6134HV Dual Supply Synchronous Buck Controller PDF資料下載
參數資料
| 型號： | SP6134HV |
| 英文描述： | Dual Supply Synchronous Buck Controller |
| 中文描述： | 雙電源同步降壓控制器 |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 141K |
| 代理商： | SP6134HV |
4
Date: 5/25/04
SP6134 Dual Supply, Synchronous Buck Controller Copyright 2004 Sipex Corporation
PIN #
1
PIN NAME DESCRIPTION
V
CC
Bias Supply Input. Connect to external 5V supply. Used to power internal circuits and
low side gate driver.
GL
High current driver output for the low side NFET switch. It is always low if GH is high or
during a fault. Resistor pull down ensure low state at low voltage.
GND
Ground Pin. The control circuitry of the IC and lower power driver are referenced to this
pin. Return separately from other ground traces to the (-) terminal of C
OUT
.
V
FB
Feedback Voltage and Short Circuit Detection pin. It is the inverting input of the Error
Amplifier and serves as the output voltage feedback point for the Buck Converter. The
output voltage is sensed and can be adjusted through an external resistor divider.
Whenever V
drops 0.25V below the positive reference, a short circuit fault is detected
and the IC enters hiccup mode.
COMP
Output of the Error Amplifier. It is internally connected to the non-inverting input of the
PWM comparator. An optimal filter combination is chosen and connected to this pin and
either ground or V
FB
to stabilize the voltage mode loop.
UVIN
UVLO input for V
voltage. Connect a resistor divider between V
IN
and UVIN to set
minimum operating voltage.
SS
Soft Start. Connect an external capacitor between SS and GND to set the soft start rate
based on the 10
μ
A source current. The SS pin is held low via a 1mA (min) current during
all fault conditions.
SWN
Lower supply rail for the GH high-side gate driver. Connect this pin to the switching node
at the junction between the two external power MOSFET transistors.
GH
High current driver output for the high side NFET switch. It is always low if GL is high or
during a fault. Resistor pull down ensure low state at low voltage.
BST
High side driver supply pin. Connect BST to the external boost diode and capacitor as
shown in the Typical Application Circuit on page 1. High side driver is connected between
BST pin and SWN pin.
2
3
4
5
6
7
8
9
10
PIN DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| SP6134HVLED | Illuminated panel mount pushbutton switch with standard red, green and yellow LED options |
| SP6134HVLEDEB | Evaluation Board Manual |
| SP6222 | 50mA and 150mA CMOS Linear Regulators |
| SP6222EC5-L | 50mA and 150mA CMOS Linear Regulators |
| SP6222EK-L | 50mA and 150mA CMOS Linear Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6134HVLED | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6134HVLEDEB | 功能描述:電源管理IC開發工具 Dual Supply Sync Buck Controller RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| SP6136 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6136_06 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP6136EB | 功能描述:DC/DC 開關控制器 Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。