- 您現在的位置：買賣IC網 > PDF目錄372186 > SP6123ACN CAP .033UF 100V PPS FILM ECH-S PDF資料下載
參數資料
| 型號： | SP6123ACN |
| 英文描述： | CAP .033UF 100V PPS FILM ECH-S |
| 中文描述： | 低，同步降壓電壓降壓PWM控制器，適合2A至10A條，占地面積小，DC - DC電源轉換器 |
| 文件頁數： | 6/18頁 |
| 文件大?。?/td> | 154K |
| 代理商： | SP6123ACN |
6
Date: 5/25/04
SP6123 Low Voltage, Synchronous Step Down PWM Controller Copyright 2004 Sipex Corporation
clamp and then gradually charges preventing
the error amplifier from forcing the loop to
maximum duty cycle. As the COMP voltage
crosses about 1V (valley voltage of the PWM
ramp), the driver begins to switch the high side
MOSFET with narrow pulses in an effort to
keep the converter output regulated . The SP6123
operates at low duty cycle as the COMP voltage
increases above 1V. As the error amp reference
ramps upward, the driver pulses widen until a
steady state value is reached and the output
voltage is regulated to the final value ending the
soft start charge cycle.
Hiccup Mode
When the converter enters a fault mode, the
SP6123 holds the high side and low side
MOSFETs off for a finite period of time. Pro-
vided that the SP6123 is enabled, this time is set
by the internal charge of the soft-start capacitor.
In the event of an overcurrent condition, the
current sense comparator sets the fault latch,
which in turn discharge the internal SS capaci-
tor, the COMP pin and holds the output drivers
off. During this condition, the SP6123 stays off
for the time it takes to discharge the COMP pin
down to the 0.27V shutdown threshold. At this
point, the fault latch is reset, but before the
SP6123 is allowed to attempt restart, the COMP
pin has to charge back to 1V before any output
switching can be initiated. Then, the regulator
attempts to restart normally by delivering short
gate pulses and if the overcurrent condition is
still present, the cycle will repeat itself. How-
ever, if upon restart, the overcurrent condition is
still present, the SP6123 will detect the fault and
remain in a fault state until COMP reaches about
V
CC
-1V thereby increasing the MOSFET off-
time. This protection scheme minimizes ther-
mal stress to the regulator components as the
overcurrent condition persists.
The simplified waveforms that describe the hic-
cup mode operation are shown below.
200 mV
3 V
0.3 V
V
COMP
1.0 V
GH
V
SWN
V
BST
V
CC
-V
SWN
Voltage
TIME
0 V
0.8 V
I(L)
TIME
0.3 V
0 V
0.7 V
1 V
V
OUT
= V
REF
* (1+R1/R2)
COMP
Internal SS
Voltage
0 V
SWN
Voltage
FAULT
Current
Inductor
0 A
Voltage
Reference
Error Amp
0 V
V(V
CC
)
0 V
V(V
CC
)
OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| SP6123CN | CAP .01UF 50V PPS FILM ECH-S |
| SP6123A | Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6123 | Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6125 | High-Voltage, Step Down Controller in TSOT6 |
| SP6125EK1L | High-Voltage, Step Down Controller in TSOT6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP6123ACN/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Low Voltage, Synchronous Step-Down PWM Controller Ideal for 2A to 10A, Small Footprint, DC-DC Power Converters |
| SP6123ACN-L | 功能描述:電壓模式 PWM 控制器 Low Voltage, Micro 8 Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6123ACN-L/TR | 功能描述:電壓模式 PWM 控制器 Low Voltage, Micro 8 Synchronous, Cntrllr RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SP6123AEN-L | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| SP6123CN | 制造商:Exar Corporation 功能描述:Swithed-Mode Power Supply Controller, Voltage Mode Type, 8 Pin, Plastic, SOP |
發布緊急采購，3分鐘左右您將得到回復。