- 您現在的位置：買賣IC網 > PDF目錄372185 > SP505RB Multi-Protocol Serial Transceivers PDF資料下載
參數資料
| 型號： | SP505RB |
| 英文描述： | Multi-Protocol Serial Transceivers |
| 中文描述： | 多協議串行收發器 |
| 文件頁數： | 20/35頁 |
| 文件大小： | 495K |
| 代理商： | SP505RB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
20
Rev: A Date: 1/27/04
SP505 Multi–Mode Serial Transceiver
Copyright 2004 Sipex Corporation
requirements of ±1.5V minimum differential
output levels with a 54
load. The driver is
designed to operate over a common mode range
of +12V to -7V, which follows the RS-485
specification. This also covers the +7V to -7V
common mode range for V.11 (RS-422) re-
quirements. The V.11 drivers are used in RS-
449, EIA-530, EIA-530A and V.36 modes as
Category I signals which are used for clock and
data signals.
V.35 Drivers
The fourth type of driver is the V.35 driver.
These drivers were specifically designed to com-
ply with the requirements of V.35. Unique to
the industry, the
Sipex's
V.35 driver architec-
ture used in the
SP505
does not need external
termination resistors to operate and comply with
V.35. This simplifies existing V.35 implemen-
tations that use external termination schemes.
The V.35 drivers can produce +0.55V driver
output signals with minimum deviation (maxi-
mum 20%) given an equivalent load of 100
.
With the help of internal resistor networks, the
drivers achieve the 50
to 150
source imped-
ance and the 135
to 165
short-circuit imped-
ance for V.35. The V.35 driver is disabled and
transparent when the decoder is in all other
modes. All of the differential drivers; V.11 (RS-
422) and V.35, can operate over 10Mbps.
Driver Enable and Input
All the drivers in the
SP505
contain individual
enable lines which can tri-state the driver out-
puts when a logic "1" is applied. This simplifies
half-duplex configurations for some applica-
tions and also provides simpler DTE/DCE
flexibility with one integrated circuit.
The driver inputs are both TTL or CMOS
compatible. Each driver input should have a
pull-down or pull-up resistor so that the output
will be at a defined state. Unused driver inputs
should not be left floating.
Receivers
The
SP505
has seven (7) independent receivers
which can be programmed for the different
interface modes. Control for the mode selection
is done via a 4–bit control word, which is the
same as the driver's 4-bit control word.
Like the drivers, the receivers are prearranged
for the specific requirements of the synchronous
Drivers
The
SP505
has seven (7) enhanced independent
drivers. Control for the mode selection is done
via a four–bit control word. The drivers are
prearranged such that for each mode of opera-
tion, the relative position and functionality of
the drivers are set up to accommodate the se-
lected interface mode. As the mode of the driv-
ers is changed, the electrical characteristics will
change to support the requirements of clock,
data, and control line signal levels.
Table 1
shows the mode of each driver in the different
interface modes that can be selected.
There are four basic types of driver circuits —
V.28, V.11, V.10 and V.35.
V.28 Drivers
The V.28 drivers output single–ended signals
with a minimum of +5V (with 3k
& 2500pF
loading), and can operate to at least 120kbps
under full load. Since the
SP505
uses a charge
pump to generate the RS-232 output rails, the
driver outputs will never exceed +10V. The
V.28 drivers are used in RS-232 mode for all
signals, and also in V.35 mode where four (4)
drivers are used as the control line signals (DTR,
RTS, LL, and RL).
V.10 Drivers
The V.10 (RS-423) drivers are also single–
ended signals which produce open circuit V
and V
measurements of +4.0V to +6.0V.
When terminated with a 450
load to ground,
the driver output will not deviate more than 10%
of the open circuit value. This is in compliance
of the ITU V.10 specification. The V.10 drivers
are used in RS-449, EIA-530, EIA-530A and
V.36 modes as Category II signals from each of
their corresponding specifications.
V.11 Drivers
The third type of driver is a V.11 (RS-422) type
differential driver. Due to the nature of differ-
ential signaling, the drivers are more immune to
noise as opposed to single-ended transmission
methods. The advantage is evident over high
speeds and long transmission lines. The strength
of the driver outputs can produce differential
signals that can maintain typically +2.2V differ-
ential output levels with a load of 100
. The
signal levels and drive capability of these driv-
ers allow the drivers to also support RS-485
相關PDF資料 |
PDF描述 |
|---|---|
| SP506 | 5V, Single Chip WAN Multi-Mode Serial Transceiver |
| SP506CF | 5V, Single Chip WAN Multi-Mode Serial Transceiver |
| SP506EB | Multi-Protocol Serial Transceivers |
| SP506EK | Multi-Protocol Serial Transceivers |
| SP506RB | Multi-Protocol Serial Transceivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP506 | 制造商:EXAR 制造商全稱:EXAR 功能描述:5V Single Chip WAN Multi-Mode Serial Transceiver |
| SP506CF | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:5V, Single Chip WAN Multi-Mode Serial Transceiver |
| SP506CF-L | 制造商:Exar 功能描述:Transceiver WAN Multi-Mode 20Mbps MQFP80 |
| SP506CM-L | 功能描述:外圍驅動器與原件 - PCI 5V SNGL CHIP WAN MULTI-MODE TRNCVR RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| SP506CM-L | 制造商:Exar Corporation 功能描述:IC WAN MULTIMODE SER TXRX 5.25V LQFP80 |
發布緊急采購，3分鐘左右您將得到回復。