- 您現在的位置：買賣IC網 > PDF目錄372172 > SP2526-1NEB Evaluation Board Manual PDF資料下載
參數資料
| 型號： | SP2526-1NEB |
| 英文描述： | Evaluation Board Manual |
| 中文描述： | 評估板手冊 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 118K |
| 代理商： | SP2526-1NEB |
SP2526EB/02
SP2526 Evaluation Board Manual
3
Copyright 2000 Sipex Corporation
V
— Connect to a second Power Supply 5V
(or 3.3V) connection – V
provides the pull-up
voltage for Enables ENA & ENB and Flags
FLGA & FLGB. This separate supply connection
allows the user to separately measure V
IN
supply
current.
GND — Second Power Supply GND Connection –
connect to supply return for V
DD
.
ENA — U1-1 —Enable A Input must be
connected High or Low – open produces
unstable behavior, so be sure to connect V
to
an external 3.3V or 5V source. See
Table 1
Enable Jumpers for information on Enable
Jumper J1 position. The user can actively
control Switch A with an external Logic signal.
FLGA — U1-2 — Flag A output is open drain
and has a pull-up to V
(which should be
connected to an external source). Connect
FLGA to voltmeter or oscilloscope to monitor
Switch A for flags when Low if Under-voltage,
Over-current or Over-temperature occurs.
.
connected High or Low – open produces
unstable behavior, so be sure to connect V
to an external 3.3V or 5V source. See
Table 1
Enable Jumpers for information on Enable
Jumper J2 position. The user can actively
control Switch B with an external Logic signal.
FLGB — U1-3 — Flag B output is open drain
and has a pull-up to V
(which should be
connected to an external source). Connect
FLGB to voltmeter or oscilloscope to monitor
Switch B for flags when Low if Under-voltage,
Over-current or Over-temperature occurs.
Using the Enable Jumbers J1 & J2
The jumpers J1& J2 have 2 positions, as
described below. Connecting a logic level to
the ENA or ENB test point post will override
the pull-up or pull-down to actively control
the switch.
Part
Number
SP2526-1
Enable A
J1 Position
1-2
Pull-up
2-3
Pull-down
Enable B
J2 Position
1-2
Pull-up
2-3
Pull-down
Enable
Active
High
Active
Low
SP2526-2
Table 1. Enable Jumpers J1 & J2
相關PDF資料 |
PDF描述 |
|---|---|
| SP2526-1 | Evaluation Board Manual |
| SP2526-1EN | +3.0V to +5.5V USB Power Control Switch |
| SP2526-2 | Evaluation Board Manual |
| SP2526EN-1 | +3.0V to +5.5V USB Power Control Switch |
| SP2526EN-2 | +3.0V to +5.5V USB Power Control Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP2526-2 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP2526-2EN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:+3.0V to +5.5V USB Power Control Switch |
| SP2526-2EN/TR | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:+3.0V to +5.5V USB Power Control Switch |
| SP2526-2EN-L | 功能描述:電源開關 IC - USB 3.0V to +5.5V USB Power Control Switch RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| SP2526-2NEB | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
發布緊急采購，3分鐘左右您將得到回復。