
SN54ALVTH162245, SN74ALVTH162245
2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCES331A
–
APRIL 2000
–
REVISED APRIL 2002
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range,
V
CC
= 2.5 V
±
0.2 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SN54ALVTH162245
MIN
TYP
SN74ALVTH162245
MIN
TYP
UNIT
MAX
MAX
VIK
VCC = 2.3 V,
VCC = 2.3 V to 2.7 V,
II =
–
18 mA
IOH =
–
100
μ
A
IOH =
–
6 mA
IOH =
–
8 mA
IOH =
–
100
μ
A
IOH =
–
6 mA
IOH =
–
8 mA
IOL = 100
μ
A
IOL = 6 mA
IOL = 12 mA
IOL = 100
μ
A
IOL = 6 mA
IOL = 8 mA
IOL = 18 mA
IOL = 24 mA
VI = GND
VI = 5.5 V
VI = 5.5 V
VI = VCC
VI = 0
VI or VO = 0 to
4.5 V
VI = 0.7 V
VI = 1.7 V
VI = 0 to VCC
VI = 0 to VCC
VO = 5.5 V
–
1.2
–
1.2
V
VCC
–
0.2
1.7
VCC
–
0.2
A port
VCC= 2 3 V
VCC = 2.3 V
VOH
1.7
V
VCC = 2.3 V to 2.7 V,
VCC
–
0.2
1.7
VCC
–
0.2
B port
VCC= 2 3 V
VCC = 2.3 V
1.7
VCC = 2.3 V to 2.7 V,
0.2
0.2
A port
VCC= 2 3 V
VCC = 2.3 V
0.4
0.4
VOL
VCC = 2.3 V to 2.7 V,
0.2
0.2
V
0.4
B port
VCC= 2 3 V
VCC = 2.3 V
0.4
0.5
0.5
±
1
10
Control inputs
VCC = 2.7 V,
VCC = 0 or 2.7 V,
±
1
10
II
20
20
μ
A
A or B ports
VCC = 2.7 V
1
1
–
5
–
5
Ioff
IBHL
IBHH
§
IBHLO
IBHHO#
IEX||
VCC = 0,
VCC = 2.3 V,
VCC = 2.3 V,
VCC = 2.7 V,
VCC = 2.7 V,
VCC = 2.3 V,
VCC
≤
1.2 V, VO = 0.5 V to VCC,
VI = GND or VCC, OE = don
’
t care
±
100
μ
A
μ
A
μ
A
μ
A
μ
A
μ
A
115
115
–
10
–
10
300
300
–
300
–
300
125
125
IOZ(PU/PD)
±
100
±
100
μ
A
VCC= 2.7 V,
VCC = 2.7 V,
IO = 0,
VI = VCC or GND
Outputs high
0.04
0.1
0.04
0.1
ICC
Outputs low
2.3
4.5
2.3
4.5
mA
Outputs disabled
0.04
0.1
0.04
0.1
Ci
Cio
VCC = 2.5 V,
VCC = 2.5 V,
VI = 2.5 V or 0
VO = 2.5 V or 0
3.5
3.5
pF
8
8
pF
All typical values are at VCC = 2.5 V, TA = 25
°
C.
The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and
then raising it to VIL max.
§
The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and
then lowering it to VIH min.
An external driver must source at least IBHLO to switch this node from low to high.
#An external driver must sink at least IBHHO to switch this node from high to low.
||Current into an output in the high state when VO > VCC
High-impedance state during power up or power down
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.