- 您現在的位置：買賣IC網 > PDF目錄378698 > SM5904BF (Seiko NPC Corporation) compression and non compression type shock-proof memory controller PDF資料下載
參數資料
| 型號： | SM5904BF |
| 廠商： | Seiko NPC Corporation |
| 英文描述： | compression and non compression type shock-proof memory controller |
| 中文描述： | 壓縮和非壓縮式防震內存控制器 |
| 文件頁數： | 25/35頁 |
| 文件大?。?/td> | 266K |
| 代理商： | SM5904BF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
NIPPON PRECISION CIRCUITS-25
SM5904BF
Compare-connect sequence
The SM5904BF supports three kinds of connect
modes; 3-pair compare-connect, 2-pair compare-
connect and direct connect.
Note that the SM5904BF can also operate in 12-bit
comparison connect mode using only the most sig-
nificant 12 bits of data for connection operation.
In 3-pair compare-connect mode, the final 6 valid
data (3 pairs of left- and right-channel data input
before encode processing) and the most recently
input data are compared until three continuous data
pairs all conform. At this point, the encode
sequence is re-started and data is written to VWA.
In 2-pair compare-connect mode, comparison
occurs just as for 3-pair comparison except that
only 2 pairs from the three compared need to con-
form with the valid data. At this point, the encode
sequence is re-started and data is written to VWA.
In direct-connect mode, comparison is not per-
formed at all, and encode sequence starts and data
is written to the VWA. This mode is for systems that
cannot perform compare-connect operation.
- Compare-connect preparation time
1. Comparison data preparation time
Internally, when the compare-connect start com-
mand is issued, a sequence starts to restore the
data for comparison. The time required for this
preparation after receiving the command is approxi-
mately 2.5
×
(1/fs). (approximately 60
μ
s when fs =
44.1 kHz)
2. After the above preparation is finished, data is
input beginning from the left-channel data and com-
parison starts.
3. If the compare-connect command is issued
again, the preparation time above is not necessary
and operation starts from step 2.
4. The same sequence takes place in direct-con-
nect mode also. However, at the point when 3
words have been input, all data is directly connect-
ed as if comparison and conformance had taken
place.
- Compare-connect sequence stop
If a compare-connect stop command (80H with
MSDCN1= 1, MSDCN2= 0) is input from the micro-
controller, compare-connect sequence stops.
If compare-connect sequence was not operating,
the compare-connect stop command performs no
operation. However, make sure that the other bit
settings within the same 80H command are valid.
相關PDF資料 |
PDF描述 |
|---|---|
| SM5904CF | compression and non compression type |
| SM5905AF | compression and non compression type shock-proof memory controller |
| SM5906AF | Shock-proof Memory Controller for Video CD Players |
| SM5907 | compression and non compression type shock-proof memory controller |
| SM5907AF | compression and non compression type shock-proof memory controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SM5904CF | 制造商:NPC 制造商全稱:Nippon Precision Circuits Inc 功能描述:compression and non compression type |
| SM5905AF | 制造商:NPC 制造商全稱:Nippon Precision Circuits Inc 功能描述:compression and non compression type shock-proof memory controller |
| SM5906AF | 制造商:NPC 制造商全稱:Nippon Precision Circuits Inc 功能描述:Shock-proof Memory Controller for Video CD Players |
| SM5907 | 制造商:NPC 制造商全稱:Nippon Precision Circuits Inc 功能描述:compression and non compression type shock-proof memory controller |
| SM5907AF | 制造商:NPC 制造商全稱:Nippon Precision Circuits Inc 功能描述:compression and non compression type shock-proof memory controller |
發布緊急采購，3分鐘左右您將得到回復。