- 您現在的位置：買賣IC網 > PDF目錄365574 > SLA7033M (SANKEN ELECTRIC CO LTD) 2-Phase Stepper Motor Unipolar Driver ICs PDF資料下載
參數資料
| 型號： | SLA7033M |
| 廠商： | SANKEN ELECTRIC CO LTD |
| 元件分類： | 運動控制電子 |
| 英文描述： | 2-Phase Stepper Motor Unipolar Driver ICs |
| 中文描述： | STEPPER MOTOR CONTROLLER, 3 A, PZFM18 |
| 封裝： | ZIP-18 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 71K |
| 代理商： | SLA7033M |
31
SLA7032M/SLA7033M
SLA7032M/SLA7033M
2-Phase Stepper Motor Unipolar Driver IC (2-Phase/1-2 Phase Excitation)
I
Outline
SLA7032M (SLA7033M) is a stepper motor driver IC developed
to reduce the number of external parts required by the conven-
tional SLA7024M (SLA7026M). This IC successfully eliminates
the need for some external parts without sacrificing the features
of SLA7024M (SLA7026M). The basic function pins are com-
patible with those of SLA7024M (SLA7026M).
I
Notes on Replacing SLA7024M (SLA7026M)
SLA7032M (SLA7033M) is pin-compatible with SLA7024M
(SLA7026M). When using the IC on an existing board, the fol-
lowing preparations are necessary:
(1) Remove the resistors and capacitors attached for setting
the chopping OFF time. (r
3
, r
4
, C
1
, and C
2
in the catalog)
(2) Remove the resistors and capacitors attached for preventing
noise in the detection voltage V
RS
from causing malfunction-
ing and short the sections from which the resistors were re-
moved using jumper wires. (r
5
, r
6
, C
3
, and C
4
in the catalog)
(3) Normally, keep pins 2 and 13 grounded because their func-
tions have changed to synchronous and asynchronous
switching (SYNC terminals). For details, see "Circuit for Pre-
venting Abnormal Noise When the Motor Is Not Running (Syn-
chronous circuit)." (Low: asynchronous, High: synchronous)
I
Circuit for Preventing Abnormal Noise When the
Motor Is Not Running (Synchronous Circuit)
A motor may generate abnormal noise when it is not running. This
phenomenon is attributable to asynchronous chopping between
phases A and B. To prevent the phenomenon, SLA7032M
(SLA7033M) contains a synchronous chopping circuit. Do not leave
Synchronous circuit operating waveform
SYNC_A
SYNC voltage : Low
SYNC voltage : High
→
Chopping asynchronous
→
Chopping synchronous
TTL, etc.
SYNC_B
SLA7032M
SLA7033M
Sync/async switching
signal
To comparator
(high impedance)
REF_A
R1
R2
3
5V
REF_B
V
REF
V
REF
waveform
V
REF
0
14
SLA7032M
SLA7033M
FET A/A
gate drive signal
40
(typ.)
40
(typ.)
FET B/B
gate drive signal
ONE SHOT
(tw=2 S)
ONE SHOT
(tw=2 S)
μ
V
REF
V
RS
Phase A
0
V
REF
V
RS
Synchronous circuit ON
Synchronous circuit OFF
Phase B
0
Application Notes
the SYNC terminals open because they are for CMOS input.
Connect TTL or similar to the SYNC terminals and switch the
SYNC terminal level high or low.
When the motor is not running, set the TTL signal high (SYNC
terminal voltage: 4 V or more) to make chopping synchronous.
When the motor is running, set the TTL signal low (SYNC terminal
voltage: 0.8 V or less) to make chopping asynchronous. If chop-
ping is set to synchronous at when the motor is running, the motor
torque deteriorates before the coil current reaches the set value.
If no abnormal noise occurs when the motor is not running,
ground the SYNC terminals (TTL not necessary).
The built-in synchronous chopping circuit superimposes a trigger
signal on the REF terminal for synchronization between the two
phases. The figure below shows the internal circuit of the REF
terminal. Since the
V
REF
varies depending on the values of R1
and R2, determine these values for when the motor is not run-
ning within the range where the two phases are synchronized.
相關PDF資料 |
PDF描述 |
|---|---|
| SLA7044 | 2-Phase Stepper Motor Unipolar Driver ICs |
| SLA7042 | 2-Phase Stepper Motor Unipolar Driver ICs |
| SLA7044M | 2-Phase Stepper Motor Unipolar Driver Ics(2相步進電機單極驅動器芯片) |
| SLA7042M | 2-Phase Stepper Motor Unipolar Driver ICs |
| SLA7042 | MICROSTEPPING, UNIPOLAR PWM, HIGH-CURRENT MOTOR CONTROLLER/DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SLA7033M-LF871 | 制造商:Sanken Electric Co Ltd 功能描述: |
| SLA7042 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:2-Phase Stepper Motor Unipolar Driver ICs |
| SLA7042M | 制造商:Allegro MicroSystems 功能描述:IC MOTOR DRIVER 制造商:Allegro MicroSystems 功能描述:IC MOTOR CTRL/DRVR, STEPPER, 1.5A SIP18; Motor Type:Stepper; No. of Outputs:4; Output Current:1.5A; Output Voltage:100V; Driver Case Style:SIP; No. of Pins:18; Supply Voltage Min:4.5V; Supply Voltage Max:5.5V; Device Type:Motor ;RoHS Compliant: Yes |
| SLA7042M_10 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:2W1-2 Phase Excitation/Micro-step Support |
| SLA7044 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:2-Phase Stepper Motor Unipolar Driver ICs |
發布緊急采購，3分鐘左右您將得到回復。