- 您現在的位置：買賣IC網 > PDF目錄373402 > SL5001P-2P (AUK Corp) TONE RINGER PDF資料下載
參數資料
| 型號： | SL5001P-2P |
| 廠商： | AUK Corp |
| 英文描述： | TONE RINGER |
| 中文描述： | 音調振鈴 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 291K |
| 代理商： | SL5001P-2P |
KSI-W012-001
4
Application Circuit And Information
1.Typical Tone Ringer
The AC ringing voltage appears across the TIP and RING inputs of the circuit and is
attenuated by capacitor(C
1
) and resistor (R
1
). C
1
also provides isolation from DC
voltages(48V) on the line. After full wave rectification by the bridge, the waveform is
filtered by capacitor(C
4
) to provide a DC supply for Tone Ringer chip. As this voltage
exceeds the initiation voltage V
CC(INI)
oscillation starts. With the components shown, the
output frequency chops between f
H1
and f
H2
at a f
L
rate. The loudspeaker load is coupled
through a 1300
to 8
transformer. To prevent DC power supply regulation problems due
to high source impedance of the telephone line and coupling components C
1
and R
1
, while
the output impedance of the 5001P circuit is quite low, the load impedance must be kept
fairly high. The output coupling capacitor (C
5
) is required with transformer coupled loads.
The variable resistor (R
6
) is used to adjust the audio amplitude and resistor (R
4
) is a
current limiting resistor. Resistor R
5
is a quenching resistor used to limit back emf
generated by the inductive load when ringing stops. When driving a piezo-ceramic
transducer type load, the coupling capacitor (C
5
) is not required. However, a current
limiting resistor is required as is a 29V zener diode in parallel with the transducer. This
diode limits the voltage transients than can be generated by mechanical shocking of piezo-
ceramic transducer.
In the 5002P circuit, the initiation supply current I
CC(INI)
can be changed by using external
resistor(R
SL
). The resistor (R
SL
) is connected to GND from pin2. As this initiation voltage
remains constant independent of R
SL
, the supply initiation current f
CC(INI)
varies inversely
with R
SL
. Thus, increasing the value of R
SL
will decrease the amount of AC ringing current
required to trigger the device. R
SL
can also be used to compensated for smaller AC line
SL5001P/2P
DBL5001
SL5002P
1
8
2
7
3
6
4
5
165K
C5
R4
510
R3
C3
R5
R2
SP
191K 0.0068uF
10K
R6
R
E
R
SL
D1
C4
C2
15K
0.22uF
0.047uF
10uF
2
TIP
1uF
2K
RING
5
5
1300 : 8
SL5001P
相關PDF資料 |
PDF描述 |
|---|---|
| SL5001P | TONE RINGER |
| SL5002P | TONE RINGER |
| SL5015 | COMPANDOR |
| SL5015P | COMPANDOR |
| SL5018 | LOW POWER NARROW BAND FM IF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SL5002P | 制造商:AUK 制造商全稱:AUK corp 功能描述:TONE RINGER |
| SL500KG-SPL1 | 制造商:Schneider Electric 功能描述:APC SILCON 500KW 480V SPARE - Bulk |
| SL500KG-SPL2 | 制造商:Schneider Electric 功能描述:APC SILCON 500KW 480V SPARE - Bulk |
| SL500KG-SPL3 | 制造商:Schneider Electric 功能描述:APC SILCON 500KW 480V SPARE - Bulk |
| SL500KG-SPL4 | 制造商:Schneider Electric 功能描述:APC SILCON 500KW 480V SPARE - Bulk |
發布緊急采購，3分鐘左右您將得到回復。