- 您現在的位置：買賣IC網 > PDF目錄8721 > SL2305ZI-1T (Silicon Laboratories Inc)IC BUFFER 140MHZ 5CH 3.3V 8TSSOP PDF資料下載
參數資料
| 型號： | SL2305ZI-1T |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC BUFFER 140MHZ 5CH 3.3V 8TSSOP |
| 標準包裝： | 2,500 |
| 系列： | EProClock® |
| 類型： | * |
| PLL： | 是 |
| 輸入： | 時鐘 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:5 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 140MHz |
| 除法器/乘法器： | 無/無 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | * |
| 封裝/外殼： | * |
| 供應商設備封裝： | * |
| 包裝： | * |
Rev 2.1, October 22, 2007
Page 7 of 11
SL2305
External Components & Design Considerations
Typical Application Schematic
SL2305
CL
0.1
μF
CLKIN
CLKOUT
CLK1
CLK4
GND
VDD
1
6
4
7
3
8
Comments and Recommendations
Decoupling Capacitor:
A decoupling capacitor of 0.1μF must be used between VDD and VSS on the pins 6 and 4. Place
the capacitor on the component side of the PCB as close to the VDD pin as possible. The PCB trace to the VDD pin and to
the GND via should be kept as short as possible. Do not use vias between the decoupling capacitor and the VDD pin.
Series Termination Resistor: A series termination resistor is recommended if the distance between the outputs and the
load is over 1 inch. The nominal impedance of the Clock outputs are
about 30 Ω. Use 20 Ω resistor in series with the
output to terminate 50Ω trace impedance and place 20 Ω resistor as close to the clock outputs as possible.
Zero Delay and Skew Control: All outputs and CLKIN pins should be loaded with the same load to achieve “Zero Delay”
between the CLKIN and the outputs. The CLKOUT pin is connected to CLKIN internally on-chip for internal feedback to
PLL, and sees an additional 2 pF load with respect to the clock pins. For applications requiring zero input/output delay, the
load at the all output pins including the CLKOUT pin must be the same. If any delay adjustment is required, the capacitance
at the CLKOUT pin could be increased or decreased to increase or decrease the delay between clocks and CLKIN.
For minimum pin-to-pin skew, the external load at the clock outputs must be the same.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J5B-MZ-F1 | CONVERTER MOD DC/DC 95V 25W |
| AD5320BRT-REEL7 | IC DAC 12BIT R-R W/BUFF SOT23-6 |
| SL2305SI-1T | IC BUFFER 140MHZ 5CH 3.3V 8SOIC |
| VI-B6X-IU-B1 | CONVERTER MOD DC/DC 5.2V 200W |
| SL2305ZI-1 | IC BUFFER 140MHZ 5CH 3.3V 8TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SL2309 | 制造商:SPECTRALINEAR 制造商全稱:SPECTRALINEAR 功能描述:Low Jitter and Skew 10 to 140MHz Zero Delay Buffer (ZDB) |
| SL2309NZ | 制造商:SPECTRALINEAR 制造商全稱:SPECTRALINEAR 功能描述:Low Jitter and Skew DC to 140 MHz Clock Buffer |
| SL2309NZSC-1 | 功能描述:時鐘緩沖器 0-140MHz 9 Fanout Buffer 3.3V Hi Drive RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL2309NZSC-1H | 功能描述:時鐘緩沖器 0-140MHz 9 Fanout Buffer 3.3V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL2309NZSC-1HT | 功能描述:時鐘緩沖器 0-140MHz 9 Fanout Buffer 3.3V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。