- 您現在的位置：買賣IC網 > PDF目錄10400 > SI9241AEY-T1 (Vishay Siliconix)IC SINGLE-ENDED BUS TXRX 8SOIC PDF資料下載
參數資料
| 型號： | SI9241AEY-T1 |
| 廠商： | Vishay Siliconix |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SINGLE-ENDED BUS TXRX 8SOIC |
| 標準包裝： | 2,500 |
| 類型： | 總線收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | ISO 9141 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOICN |
| 包裝： | 帶卷 (TR) |
www.vishay.com
4
Document Number: 70787
S11-0975-Rev. F, 16-May-11
Vishay Siliconix
Si9241A
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Product is End of Life 3/2014
PIN CONFIGURATION
FUNCTIONAL DESCRIPTION
The Si9241AEY can be either in transmit or receive mode
and it contains over temperature, and short circuit VBAT fault
detection circuits.
The voltage on K is internally compared to VBAT/2. If the
voltage on the K pin is less than VBAT/2 then RX output will
be "low". If the voltage on the K pin is greater than VBAT/2
then RX output will be "high".
In order to be in transmit mode, CS must be set "low". When
CS and TX are set "low" the internal MOSFET will turn on,
causing the K pin to be "low". In the transmit mode, the
processor monitors RX and TX. When the two mirror each
other there is no fault. In the event of over temperature, or
short circuit to VBAT, the Si9241AEY will turn off the K output
to protect the IC and the external open drain FAULT pin will
be asserted. The K pin will stay in high impedance and RX
will follow the K pin. The fault will be reset when CS is toggled
high. RX, CS and TX pins have an internal pull up resistor to
VDD while the K pin has internal pull down resistors. When
any one of the TX, VBAT or GND pins is open the K output is
off.
When CS is set "high" the Si9241AEY is in receive mode and
the internal MOSFET for the K pin is turned off. The RX
output will follow the K pin. If CS is "low" while the IC is
receiving data, an incorrect fault signal will occur.
To inhibit the short detect, tie CS and TX together.
1
2
3
4
5
6
7
8
Top View
Narrow Body
TX
VDD
FAULT
VBAT
K
GND
SO Package
CS
RX
ORDERING INFORMATION
Part Number
Temperature Range
Si9241AEY-T1
- 40 °C to 125 °C
Si9241AEY-T1-E3 (Lead (Pb)-free)
PIN DESCRIPTION
Pin Number
Symbol
Description
1
VDD
Positive Power Supply
2
TX
Transmit, Input
3CS
Chip Select, Input
4FAULT
Fault, Open Drain Output
5
GND
Ground Connection
6
K
Transmit/Receive, Bidirectional
7
VBAT
Battery Power Supply
8
RX
Receiver, Output
相關PDF資料 |
PDF描述 |
|---|---|
| MS27499E10A13PLC | CONN HSG RCPT 13POS BOX MNT PINS |
| VE-J6K-MW-F4 | CONVERTER MOD DC/DC 40V 100W |
| SI9241AEY-E3 | IC SINGLE-ENDED BUS TXRX 8SOIC |
| VE-J6K-MW-F2 | CONVERTER MOD DC/DC 40V 100W |
| VE-J6J-MW-F2 | CONVERTER MOD DC/DC 36V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI9241AEY-T1-E3 | 功能描述:總線收發器 Bus Tranceiver RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SI9241AEY-T1-E3 | 制造商:Vishay Siliconix 功能描述:Bus Transceiver IC |
| SI9241EY | 功能描述:CAN 接口集成電路 Bus Tranceiver RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| SI9241EY-T1 | 制造商:Vishay Angstrohm 功能描述:Single Transmitter/Receiver 8-Pin SOIC N T/R |
| SI9243A | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Single-Ended Bus Transceiver |
發布緊急采購，3分鐘左右您將得到回復。