- 您現在的位置：買賣IC網 > PDF目錄365561 > Si9183 (Vishay Intertechnology,Inc.) High-Performance, Size Saving 150-mA CMOS LDO Regulator(高性能輸出電流150mA的CMOS低壓差穩壓器) PDF資料下載
參數資料
| 型號： | Si9183 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | High-Performance, Size Saving 150-mA CMOS LDO Regulator(高性能輸出電流150mA的CMOS低壓差穩壓器) |
| 中文描述： | 高性能，尺寸保留150毫安的CMOS LDO穩壓器（高性能輸出電流為150mA的的CMOS低壓差穩壓器） |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 101K |
| 代理商： | SI9183 |
Si9183
Vishay Siliconix
New Product
www.vishay.com
10
Document Number: 71258
S-02730
—
Rev. C, 12-Dec-00
The Si9183 is a low drop out, low quiescent current, linear
regulator family with very fast transient response. It is primarily
designed for battery powered applications where battery run
time is at a premium. The low quiescent current allows
extended standby time while low drop out voltage enables the
system to fully utilize battery power before recharge. The
Si9183 is a very fast regulator with bandwidth exceeding
50 kHz while maintaining low quiescent current at light load
conditions. With this bandwidth, the Si9183 is one of the
fastest LDO available today. The Si9183 is stable with one of
any output capacitor types from 1 F to 10.0 F. However,
X5R or X7R ceramic capacitors are recommended for best
output noise and transient performance.
V
IN
V
IN
is the input supply pin. The bypass capacitor for this pin
is not critical as long as the input supply has low enough source
impedance. For practical circuits, a 1.0- F or larger ceramic
capacitor is recommended. When the source impedance is
not low enough and/or the source is several inches from the
Si9183, then a larger input bypass capacitor is needed. It is
required that the equivalent impedance (source impedance,
wire, and trace impedance in parallel with input bypass
capacitor impedance) must be smaller than the input
impedance of the Si9183 for stable operation. When the
source impedance, wire, and trace impedance are unknown,
it is recommended that an input bypass capacitor be used of
a value that is equal to or greater than the output capacitor.
V
OUT
V
OUT
is the output voltage of the regulator. Connect a bypass
capacitor from V
OUT
to ground. The output capacitor can be
any value from 1.0 F to 10.0 F. A ceramic capacitor with
X5R or X7R dielectric type is recommended for best output
noise, line transient, and load transient performance.
GND
Ground is the common ground connection for V
IN
and V
OUT
.
It is also the local ground connection for C
BP
, ADJ, and SD.
ADJ
For the adjustable output version, use a resistor divider R1 and
R2, connect R1 from V
OUT
to ADJ and R2 from ADJ to ground.
R2 should be in the 25-k to 150-k range for low power
consumption, while maintaining adequate noise immunity.
The formula below calculates the value of R1, given the
desired output voltage and the R2 value,
(1)
R1
V
OUT
V
ADJ
R2
V
ADJ
V
ADJ
is nominally 1.215 V.
SHUTDOWN (SD)
SD controls the turning on and off of the Si9183. V
OUT
is
guaranteed to be on when the SD pin voltage equals or is
greater than 1.5 V. V
OUT
is guaranteed to be off when theSD
pin voltage equals or is less than 0.4 V. During shutdown
mode, the Si9183 will draw less than 1- A current from the
source. To automatically turn on V
OUT
whenever the input is
applied, tie the SD pin to V
IN
.
C
BP
For low noise application, connect a high frequency ceramic
capacitor from C
BP
to ground. A 0.01- F or a 0.1- F X5R or
X7R is recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| Si91843DT-50-T1 | 150-mA Ultra Low-Noise LDO Regulator With Discharge Option |
| Si91841DT-28-T1 | 150-mA Ultra Low-Noise LDO Regulator With Discharge Option |
| Si91841DT-285-T1 | 150-mA Ultra Low-Noise LDO Regulator With Discharge Option |
| Si91841DT-29-T1 | 150-mA Ultra Low-Noise LDO Regulator With Discharge Option |
| Si91841DT-30-T1 | 150-mA Ultra Low-Noise LDO Regulator With Discharge Option |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI9183_05 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:High-Performance, Size Saving 150-mA CMOS LDO Regulator |
| SI9183DB | 功能描述:低壓差穩壓器 - LDO SI9183 Demo Board RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| SI9183DT-15-T1 | 功能描述:低壓差穩壓器 - LDO 150mA 1.5V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| SI9183DT-18-T1 | 功能描述:低壓差穩壓器 - LDO 150mA 1.8V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| SI9183DT-18-T1-E3 | 功能描述:低壓差穩壓器 - LDO 150mA 1.8V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。