- 您現在的位置：買賣IC網 > PDF目錄365560 > Si91821DH-AD-T1-E3 (Vishay Intertechnology,Inc.) Micropower 300-mA CMOS LDO Regulator With Error Flag PDF資料下載
參數資料
| 型號： | Si91821DH-AD-T1-E3 |
| 廠商： | Vishay Intertechnology,Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Micropower 300-mA CMOS LDO Regulator With Error Flag |
| 中文描述： | 微300毫安的CMOS LDO穩壓器國旗錯誤 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 136K |
| 代理商： | SI91821DH-AD-T1-E3 |
Si91821
Vishay Siliconix
www.vishay.com
6
Document Number: 71614
S-51147–Rev. E, 20-Jun-05
DETAILED DESCRIPTION
The Si91821 is a low drop out, low quiescent current, and very
linear regulator with very fast transient response. It is primarily
designed for battery powered applications where battery run
time is at a premium. The low quiescent current allows
extended standby time while low drop out voltage enables the
system to fully utilize battery power before recharge. The
Si91821 is a very fast regulator with bandwidth exceeding
50 kHz while maintaining low quiescent current at light load
conditions. With this bandwidth, the Si91821 is the fastest
LDO available today. The Si91821 is stable with any output
capacitor type from 1 F to 10.0 F. However, X5R or X7R
ceramic capacitors are recommended for best output noise
and transient performance.
V
IN
V
IN
is the input supply pin. The bypass capacitor for this pin
is not critical as long as the input supply has low enough source
impedance. For practical circuits, a 1.0- F or larger ceramic
capacitor is recommended. When the source impedance is
not low enough and/or the source is several inches from the
Si91821, then a larger input bypass capacitor is needed. It is
required that the equivalent impedance (source impedance,
wire, and trace impedance in parallel with input bypass
capacitor impedance) must be smaller than the input
impedance of the Si91821 for stable operation. When the
source impedance, wire, and trace impedance are unknown,
it is recommended that an input bypass capacitor be used of
a value that is equal to or greater than the output capacitor.
V
OUT
V
OUT
is the output voltage of the regulator. Connect a bypass
capacitor from V
OUT
to ground. The output capacitor can be
any value from 1.0 F to 10.0 F. A ceramic capacitor with
X5R or X7R dielectric type is recommended for best output
noise, line transient, and load transient performance.
GND
Ground is the common ground connection for V
IN
and V
OUT
.
It is also the local ground connection for C
NOISE
, SET, and SD.
SET
SET is not connected internally for the fixed voltage version.
Therefore, it can be connected to GND optionally. For the
adjustable output version, use a resistor divider R
1
and R
2
,
connect R
1
from V
OUT
to SET and R
2
from SET to ground. R
2
should be in the 25-k to 150-k range for low power
consumption, while maintaining adequate noise immunity.
The formula below calculates the value of R
1
, given the
desired output voltage and the R
2
value.
R
1
V
OUT
V
SET
R
2
V
SET
(1)
V
SET
is nominally 1.215 V.
SHUTDOWN (SD)
SD controls the turning on and off of the Si91821. V
OUT
is
guaranteed to be on when the SD pin voltage equals or is
greater than 1.5 V. V
OUT
is guaranteed to be off when the SD
pin voltage equals or is less than 0.4 V. During shutdown
mode, the Si91821 will draw less than 2- A current from the
source. To automatically turn on V
OUT
whenever the input is
applied, tie the SD pin to V
IN
.
ERROR
ERROR is an open drain output that goes low when V
OUT
is
less than 5% of its normal value. As with any open drain output,
an external pull up resistor is needed. This function is active
in shutdown.
The ERROR pin must be left opened if not used.
C
NOISE
For low noise application, connect a high frequency ceramic
capacitor from C
NOISE
to ground. A 0.01- F or a 0.1- F X5R
or X7R is recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| Si91821DH-18-T1 | Micropower 300-mA CMOS LDO Regulator With Error Flag |
| Si91821DH-18-T1-E3 | Micropower 300-mA CMOS LDO Regulator With Error Flag |
| Si91821DH-25-T1 | Micropower 300-mA CMOS LDO Regulator With Error Flag |
| SI91821DB | Micropower 300-mA CMOS LDO Regulator With Error Flag |
| Si91821DH-25-T1-E3 | Micropower 300-mA CMOS LDO Regulator With Error Flag |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI91822 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Micropower 300-mA CMOS LDO Regulator With Error Flag/Power-On-Reset |
| SI91822DB | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Micropower 300-mA CMOS LDO Regulator With Error Flag/Power-On-Reset |
| SI91822DH-12-T1 | 功能描述:低壓差穩壓器 - LDO 300mA 1.2V CMOS LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| SI91822DH-12-T1-E3 | 功能描述:低壓差穩壓器 - LDO 300mA 1.2V CMOS LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| SI91822DH-15-T1 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Micropower 300-mA CMOS LDO Regulator With Error Flag/Power-On-Reset |
發布緊急采購，3分鐘左右您將得到回復。