- 您現在的位置：買賣IC網 > PDF目錄368621 > SI9160 (Vishay Intertechnology,Inc.) Controller for RF Power Amplifier Boost Converter PDF資料下載
參數資料
| 型號： | SI9160 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Controller for RF Power Amplifier Boost Converter |
| 中文描述： | 射頻功率放大器控制器升壓轉換器 |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 119K |
| 代理商： | SI9160 |
Si9160
Vishay Siliconix
www.vishay.com
10
Document Number: 70029
S-40700—Rev. H, 19-Apr-04
Energy Storage Components
The input and output ripple voltage is determined by the
switching frequency, and the inductor and capacitor values.
The higher the frequency, inductance, or capacitance values,
the lower the ripple. The efficiency of the converter is also
improved with higher inductance by reducing the conduction
loss in the switch, synchronous rectifier, and the inductor itself.
In the past, Tantalum was the preferred material for the input
and output capacitors. Now, with 2-MHz switching
frequencies, Tantalum capacitors are being replaced with
smaller surface mount ceramic capacitors. Ceramic
capacitors have almost no equivalent series resistance (ESR).
Tantalum capacitors have at least 0.1- ESR. By reducing
ESR, converter efficiency is improved while decreasing the
input and output ripple voltage. With ceramic capacitors,
output ripple voltage is a function of capacitance only. The
equation for determining output capacitance is stated below.
C
I
OUT
V
OUT
(V
OUT
– V
IN
)
V
RIPPLE
f
I
OUT
= output dc load current
V
OUT
= output voltage
V
IN
= input voltage
V
RIPPLE
= desired output ripple voltage
f = switching frequency
The inductance value for the converter is a function of the
desired ripple voltage and efficiency as stated below. In order
to keep the ripple small and improve efficiency, the inductance
needs to be large enough to maintain continuous current
mode. Continuous current mode has lower RMS current
compared to discontinuous current mode since the peak
current is lower. This lowers the conduction loss and improves
efficiency. The equation that shows the critical inductance
which separates continuous and discontinuous current mode
at any given output current is stated below. This equation is
also plotted in Figure 5 as a function of input voltage.
Designed with small surface mount inductors and capacitors,
the Si9160 solution can fit easily within a small space such as
a battery pack. Another distinct advantage of a smaller
converter size is that it reduces the noise generating area by
reducing the high current path; therefore radiated and
conducted noise is less likely to couple into sensitive circuits.
FIGURE 5.
Continuous and Discontinuous Inductance Curve
L
V
IN2
2
V
OUT
– V
IN
V
OUT
2
I
OUT
f
= efficiency
2.5
3.0
3.5
4.0
4.5
0.3
0.4
0.5
0.6
0.7
L
V
IN
(V)
Discontinuous Mode
Continuous Mode
= 0.9
V
OUT
= 5 V
I
= 0.5 A
f = 1 MHz
RESULTS SECTION
The following section shows the actual results obtained with
the circuit diagram shown in Figure 1.
Efficiency
The Figure 6 shows the efficiency of the above design at
various constant switching frequencies. The frequencies were
generated using a 3-V square wave of the desired frequency
to the sync input to the circuit. The input voltage to the circuit
is 3.6-V dc.
Output Noise
The noise generated by a dc-dc converter is always an issue
within the mobile phone. The Si9160 offers two benefits.
The noise spectrum is a constant, i.e. no random noise or
random harmonic generation.
The switching fundamental can be synchronized to a
known frequency, e.g. 812.5 kHz which is
1
/
16
-th of the
GSM/DCS system clock, 1.23 MHz which is the channel
spacing frequency for CDMA, etc.
Figures 7 through 9 show the output noise and output
spectrum analysis.
Output Noise Spectrum
Note there is no random noise, only switching frequency
harmonics. This is very good news for the RF stages, where
an unknown, or random noise spectrum will cause problems.
相關PDF資料 |
PDF描述 |
|---|---|
| Si9160BQ-T1 | Controller for RF Power Amplifier Boost Converter |
| Si9160BQ-T1-E3 | Controller for RF power amplifier boost |
| SI9165 | High Frequency 600-mA Synchronous Buck/Boost Converter |
| SI9166 | High Frequency Programmable Topology Controller |
| SI9167 | High-Frequency, High-Efficiency Buck Converter Design For Multi-Cell Battery Configured Systems Using Si9167 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI9160BQ-T1 | 功能描述:直流/直流開關轉換器 2MHz Controller RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| SI9160BQ-T1-E3 | 功能描述:DC/DC 開關控制器 Boost Conv For RF Pwr Amp RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SI9160DB | 功能描述:電源管理IC開發工具 SI9160 Demo Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| SI9161 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Optimized-Efficiency Controller for RF Power Amplifier Boost Converter |
| SI9161BQ-T1 | 功能描述:DC/DC 開關控制器 Opt-Efficiency Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。