- 您現在的位置：買賣IC網 > PDF目錄368621 > Si9145BQ-T1 (Vishay Intertechnology,Inc.) Low-Voltage Switchmode Controller PDF資料下載
參數資料
| 型號： | Si9145BQ-T1 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Low-Voltage Switchmode Controller |
| 中文描述： | 低電壓開關模式控制器 |
| 文件頁數： | 9/10頁 |
| 文件大?。?/td> | 74K |
| 代理商： | SI9145BQ-T1 |
Si9145
Vishay Siliconix
Document Number: 70021
S-40710—Rev. K, 19-Apr-04
www.vishay.com
9
Pin 9: R
OSC
This pin is the equivalent of a 1.0-V voltage source derived
from the on-chip V
REF
. When a low T.C. resistor is externally
connected from this pin to GND, a temperature independent
current is generated internally. This current is used as the
charging current source connected to the C
OSC
pin. The
current is internally multiplied by 2 and is used as the
discharging current source connected to the C
OSC
pin.
Therefore, the external resistor is one of the factors that
determine the oscillator frequency.
Pin 10: C
OSC
An external capacitor is connected to this pin to set the
oscillator frequency. Internal current sources alternately
charge and discharge the external capacitor. The oscillator
waveform is a symmetrical triangular type with a typical voltage
swing between 1.0 V and 1.5 V.
f
OSC
0.7
R
OSC
C
OSC
Pin 11: OTS
This pin indicates an over-temperature condition on the device
when the output is low. The output is latched low and is reset
with the ENABLE pin going low then high, or by turning power
off and on.
Pin 12: ENABLE
A logic high on this pin allows normal operation. A logic low
places the chip in the standby mode. In standby mode normal
operation is disabled, supply current is reduced, the oscillator
stops and the output is held high for MODE SELECT = low, and
low for MODE SELECT = high.
Pin 13: UVLO
SET
This pin will place the chip in the standby mode if the UVLO
SET
voltage drops below 1.2 V. Once the UVLO
SET
voltage
exceeds 1.2 V, the chip operates normally. There is a built-in
hysteresis of 200 mV.
Pin 14: P
GND
The negative return for the V
S
supply.
Pin 15: OUTPUT
This CMOS push-pull output pin drives the external MOSFET
and is capable of sinking 150 mA or sourcing 130 mA with V
S
equal to 2.7 V.
Pin 16: V
S
The positive terminal of the power supply which powers the
CMOS output driver. A bypass capacitor is required.
相關PDF資料 |
PDF描述 |
|---|---|
| Si9145BQ-T1-E3 | Low-Voltage Switchmode Controller |
| SI9160 | Controller for RF Power Amplifier Boost Converter |
| Si9160BQ-T1 | Controller for RF Power Amplifier Boost Converter |
| Si9160BQ-T1-E3 | Controller for RF power amplifier boost |
| SI9165 | High Frequency 600-mA Synchronous Buck/Boost Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI9145BQ-T1-E3 | 功能描述:DC/DC 開關控制器 Lo V-Hi Freq Swmode Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SI9145BY | 功能描述:電壓模式 PWM 控制器 Low Volt SMP Cont RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SI9145BY | 制造商:Vishay Siliconix 功能描述:PWM CONTROLLER SMD 9145 SOIC16 |
| SI9145BY-E3 | 功能描述:DC/DC 開關控制器 Lo V-Hi Freq Swmode Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SI9145BY-T1 | 功能描述:電壓模式 PWM 控制器 Lo V-Hi Freq Swmode Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。