- 您現在的位置：買賣IC網 > PDF目錄368621 > SI9140 (Vishay Intertechnology,Inc.) SMP Controller For High Performance Process Power Supplies PDF資料下載
參數資料
| 型號： | SI9140 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | SMP Controller For High Performance Process Power Supplies |
| 中文描述： | SMP的高性能控制器過程電源 |
| 文件頁數： | 7/15頁 |
| 文件大?。?/td> | 470K |
| 代理商： | SI9140 |
Si9140
Vishay Siliconix
FaxBack 408-970-5600, request 70026
www.siliconix.com
S-58034—Rev. G, 15-Mar-99
7
PIN CONFIGURAT IONS
PIN DES CRIPT ION
Pin 1: V
DD
The positive power supply for all functional blocks except
output driver. A bypass capacitor of 0.1 μF (minimum) is
recommended.
Pin 2: MON
Non-inverting input of a comparator. Inverting input is tied
internally to reference voltage. This comparator is typically
used to monitor the output voltage and to flag the processor
when the output voltage falls out of regulation.
Pin 3: V
GOOD
This is an open drain output. It will be held at ground when
the voltage at MON (Pin 2) is less than the internal reference.
An external pull-up resistor will pull this pin high if the MON
pin (Pin 2) is higher than the V
REF
. (Refer to Pin 2
description.)
Pin 4: COMP
This pin is the output of the error amplifier. A compensation
network is connected from this pin to the FB pin to stabilize
the system. This pin drives one input of the internal pulse
width modulation comparator.
Pin 5: FB
The inverting input of the error amplifier. An external resistor
divider is connected to this pin to set the regulated output
voltage. The compensation network is also connected to this
pin.
Pin 6: NI
The non-inverting input of the error amplifier. In normal
operation it is externally connected to V
REF
or an external
reference.
Pin 7: V
REF
This pin supplies a 1.5-V reference.
Pin 8: GND (Ground)
Pin 9: ENABLE
A logic high on this pin allows normal operation. A logic low
places the chip in the standby mode. In standby mode normal
operation is disabled, supply current is reduced, the oscillator
stops and D
S
goes high while D
R
goes low.
ORDE RING INFORMAT ION
Temperature Range
Part Number
0° to 70°C
Si9140CY
-40° to 85°C
Si9140DY
ORDE RING INFORMAT ION
Temperature Range
Part Number
0° to 70°C
Si9140CQ
-40° to 85°C
Si9140DQ
相關PDF資料 |
PDF描述 |
|---|---|
| SI9140CQ | SMP Controller For High Performance Process Power Supplies |
| SI9140CY | SMP Controller For High Performance Process Power Supplies |
| SI9140DQ | SMP Controller For High Performance Process Power Supplies |
| SI9140DY | SMP Controller For High Performance Process Power Supplies |
| SI9145 | Low-Voltage Switchmode Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI9140CQ | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:SMP Controller For High Performance Process Power Supplies |
| SI9140CQ-T1 | 功能描述:電壓模式 PWM 控制器 SMP Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SI9140CQ-T1-E3 | 功能描述:電壓模式 PWM 控制器 Switching Power Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SI9140CY | 功能描述:電壓模式 PWM 控制器 SMP Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| SI9140CY-E3 | 功能描述:電壓模式 PWM 控制器 Switching Power Supply Controller RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。