- 您現在的位置：買賣IC網 > PDF目錄8713 > SI5330C-A00208-GM (Silicon Laboratories Inc)IC CLK BUFFER TRANSLA 1:4 24-QFN PDF資料下載
參數資料
| 型號： | SI5330C-A00208-GM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 20/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK BUFFER TRANSLA 1:4 24-QFN |
| 標準包裝： | 490 |
| 類型： | 扇出緩沖器（分配），變換器 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:4 |
| 差分 - 輸入:輸出： | 是/是 |
| 輸入： | CML，CMOS，HCSL，HSTL，LVDS，LVPECL，LVTTL，SSTL |
| 輸出： | HCSL |
| 頻率 - 最大： | 250MHz |
| 電源電壓： | 1.71 V ~ 3.63 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 24-QFN（4x4） |
| 包裝： | 托盤 |
Si5330
Rev. 1.1
9
2. Functional Description
The Si5330 is a low-jitter, low-skew fanout buffer
optimized for high-performance PCB clock distribution
applications. The device produces four differential or
eight single-ended, low-jitter output clocks from a single
input clock. The input can accept either a single-ended
or a differential clock allowing the device to function as a
clock level translator.
2.1. VDD and VDDO Supplies
The core VDD and output VDDO supplies have separate
and independent supply pins allowing the core supply to
operate at a different voltage than the I/O voltage levels.
The VDD supply powers the core functions of the device,
which operates from 1.8, 2.5, or 3.3 V. Using a lower
supply voltage helps minimize the device’s power
consumption. The VDDO supply pins are used to set the
output signal levels and must be set at a voltage level
compatible with the output signal format.
2.2. Loss Of Signal Indicator (LOS)
The input is monitored for a valid clock signal using an
LOS circuit that monitors input clock edges and
declares an LOS condition when signal edges are not
detected over a 1 to 5 μs observation period. The LOS
is present. A “high” level on the LOS pin indicates a loss
of signal (LOS). The LOS pin must be pulled to VDD as
shown in Figure 2.
Figure 2. LOS Indicator with External Pull-Up
2.3. Output Enable (OEB)
The output enable (OEB) pin allows disabling or
enabling of the outputs clocks (CLK0-CLK3). The output
enable is logically controlled to ensure that no glitches
or runt pulses are generated at the output as shown in
Figure 3. OEB Glitchless Operation
All outputs are enabled when the OEB pin is connected
to ground or below the VIL voltage for this pin.
Connecting the OEB pin to VDD or above the VIH level
will disable the outputs. Both VIL and VIH are specified
in Table 5. All outputs are forced to a logic “l(fā)ow” when
disabled. The OEB pin is 3.3 V tolerant.
2.4. Input Signals
The Si5330 can accept single-ended and differential
input clocks. See “AN408: Termination Options for Any-
Frequency, Any-Output Clock Generators and Clock
Buffers—Si5338, Si5334, Si5330” for details on
connecting a wide variety of signals to the Si5330
inputs.
2.5. Output Driver Formats
The Si5330 supports single-ended output formats of
CMOS, SSTL, and HSTL and differential formats of
LVDS, LVPECL, and HCSL. It is normally required that
the LVDS driver be dc-coupled to the 100
termination
at the receiver end. If your application requires an ac-
coupled 100
load, contact the applications team for
advice. See AN408 for additional information on the
terminations for these driver types.
2.6. Input and Output Terminations
See AN408 for detailed information.
3. Ordering the Si5330
The Si5330 can be ordered to meet the requirements of
the most commonly-used input and output signal types,
such as CMOS, SSTL, HSTL, LVPECL, LVDS, and
HSCL. See Figure 1, “Si5330 Functional Block
and Device Functionality,” on page 14 for specific
ordering information.
Si5330
Control
LOS
IN
VDDO0
CLK0
VDDO1
CLK1
VDDO2
CLK2
VDDO3
CLK3
VDD
1k
Valid Clock
No Clock
0
1
IN
CLKn
OEB
Enable
Disable
Enable
相關PDF資料 |
PDF描述 |
|---|---|
| IDT74FCT20807QGI8 | IC CLK BUFF 1:10 166MHZ 20-QSOP |
| VE-J3Y-MY | CONVERTER MOD DC/DC 3.3V 33W |
| VE-J3Y-MX | CONVERTER MOD DC/DC 3.3V 49.5W |
| IDT74FCT807BTQG | IC CLK BUFFER 1:10 100MHZ 20QSOP |
| IDT5T9050PGGI8 | IC CLK BUFF 1:5 200MHZ 28-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI5330C-A00208-GMR | 功能描述:時鐘緩沖器 Diff In 2.5V output 1:4 ClkBuff 5-250MHz RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| Si5330C-A00209-GM | 功能描述:時鐘緩沖器 Diff 1.8V HCLS 4-out, 5 to 250 MHz RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SI5330C-A00209-GMR | 功能描述:時鐘緩沖器 Diff In 1.8V output 1:4 ClkBuff 5-250MHz RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SI5330C-A-GN | 制造商:Silicon Laboratories Inc 功能描述:NON PLL CLOCK FANOUT BUFFER, 5-350MHZ - Trays |
| Si5330C-B00207-GM | 功能描述:時鐘緩沖器 Diff input HCSL out 5 - 250 MHz RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。