- 您現在的位置：買賣IC網 > PDF目錄376353 > Si4826DY (National Semiconductor Corporation) N-Channel FET Synchronous Buck Regulator Controller for Low Output Voltages PDF資料下載
參數資料
| 型號： | Si4826DY |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | N-Channel FET Synchronous Buck Regulator Controller for Low Output Voltages |
| 中文描述： | N溝道場效應管同步降壓穩壓控制器輸出電壓低 |
| 文件頁數： | 2/22頁 |
| 文件大?。?/td> | 602K |
| 代理商： | SI4826DY |
Connection Diagram
20049411
14-Lead Plastic TSSOP
θ
= 155C/W
NS Package Number MTC14
Pin Description
BOOT (Pin 1)
- Supply rail for the N-channel MOSFET gate
drive. The voltage should be at least one gate threshold
above the regulator input voltage to properly turn on the
high-side N-FET.
LG (Pin 2)
- Gate drive for the low-side N-channel MOSFET.
This signal is interlocked with HG to avoid shoot-through
problems.
PGND (Pins 3, 13)
- Ground for FET drive circuitry. It should
be connected to system ground.
SGND (Pin 4)
- Ground for signal level circuitry. It should be
connected to system ground.
V
CC
(Pin 5)
- Supply rail for the controller.
PWGD (Pin 6)
- Power Good. This is an open drain output.
The pin is pulled low when the chip is in UVP, OVP, or UVLO
mode. During normal operation, this pin is connected to V
CC
or other voltage source through a pull-up resistor.
ISEN (Pin 7)
- Current limit threshold setting. This sources a
fixed 50μA current. A resistor of appropriate value should be
connected between this pin and the drain of the low-side
FET.
EAO (Pin 8)
- Output of the error amplifier. The voltage level
on this pin is compared with an internally generated ramp
signal to determine the duty cycle. This pin is necessary for
compensating the control loop.
SS (Pin 9)
- Soft start pin. A capacitor connected between
this pin and ground sets the speed at which the output
voltage ramps up. Larger capacitor value results in slower
output voltage ramp but also lower inrush current.
FB (Pin 10)
- This is the inverting input of the error amplifier,
which is used for sensing the output voltage and compen-
sating the control loop.
FREQ (Pin 11)
- The switching frequency is set by connect-
ing a resistor between this pin and ground.
SD (Pin 12)
- IC Logic Shutdown. When this pin is pulled low
the chip turns off the high side switch and turns on the low
side switch. While this pin is low, the IC will not start up. An
internal 20μA pull-up connects this pin to V
CC
.
HG (Pin 14)
- Gate drive for the high-side N-channel MOS-
FET. This signal is interlocked with LG to avoid shoot-
through problems.
L
www.national.com
2
相關PDF資料 |
PDF描述 |
|---|---|
| Si4442DY | N-Channel FET Synchronous Buck Regulator Controller for Low Output Voltages |
| SIDC03D60C6 | Fast switching diode chip in EMCON 3 -Technology |
| SIDC03D60F6 | Fast switching diode chip in EMCON-Technology |
| SIDC04D60F6 | Fast switching diode chip in EMCON-Technology |
| SIDC06D120E6 | Fast switching diode chip in EMCON-Technology |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI4826DY-T1 | 制造商:Vishay Angstrohm 功能描述:Trans MOSFET N-CH 30V 5.3A/7A 8-Pin SOIC N T/R |
| Si4827-A10-CS | 功能描述:射頻接收器 AM/FM/SW RX,16p SOIC RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| Si4827-A10-CSR | 功能描述:射頻接收器 AM/FM/SW RX,16p SOIC RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| SI4828DY | 功能描述:MOSFET 30V 7.5/9.6A RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| SI4828DY-T1 | 制造商:Vishay Angstrohm 功能描述:Trans MOSFET N-CH 30V 5.8A/7.5A 8-Pin SOIC N T/R |
發布緊急采購，3分鐘左右您將得到回復。