- 您現在的位置：買賣IC網 > PDF目錄365549 > SI4730EY (Vishay Intertechnology,Inc.) Current-Sensing Power MOSFETs PDF資料下載
參數資料
| 型號： | SI4730EY |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Current-Sensing Power MOSFETs |
| 中文描述： | 電流感應功率MOSFET |
| 文件頁數： | 1/4頁 |
| 文件大?。?/td> | 68K |
| 代理商： | SI4730EY |
AN606
Vishay Siliconix
Document Number: 71991
17-Dec-03
www.vishay.com
1
Current-Sensing Power MOSFETs
Kandarp Pandya
INTRODUCTION
Vishay Siliconix current-sensing power MOSFETs offer a
simple means of incorporating a protection feature into an
electronic control circuit and avoiding catastrophic failures
resulting from overcurrent (overload) and/or short-circuit
conditions. The device package is a modified D
2
PAK with five
pins. The MOSFET termination retains the standard D
2
PAK
footprint for a three-pin device. The additional two pins provide
termination for a current-sense output and an internal Kelvin
connection to the source. For current sensing, the MOSFET
design employs a small number of the total number of
MOSFET cells in a known ratio. The latter define the
current-sense parameters. A typical control interface uses a
simple circuit with an op-amp or a comparator. This approach
offers the freedom of control-level setting and facilitates its
incorporation into the main control system.
DEVICE DESCRIPTION AND PRINCIPLE OF
OPERATION
KELVIN
D (Tab, 3)
G
S (5)
N-Channel MOSFET
D
2
PAK-5
S
G
D
SENSE
5
1
3
2
4
SENSE
(1)
(2)
(4)
KELVIN
FIGURE 1.
Package Information and Schematic Symbol
Package Information and Schematic Symbol, Figure 1, shows a
partial reproduction of a datasheet for a current-sensing
MOSFET, SUM50N03-13C. Gate, drain-stub/tab, and source
(pins 1, 2, and 3) are in the same position as in a standard D
2
PAK
(TO-263) MOSFET. However, pin-out modification is required to
incorporate current-sense (pin 2) and Kelvin-to-source (pin 4)
between gate and drain-stub and between drain-stub and source,
respectively. See Application Note 826,
Recommended Minimum
Pad Patterns With Outline Access for Vishay Siliconix
MOSFET
s
http://www.vishay.com/doc72286),
Modified-part library symbols for schematic symbol and PCBlayout are available on the “Protel” (PCB design software)
platform. For soft copy, please contact Vishay Siliconix in Santa
Clara, Calif., in the United States, by phoning 1-408-567-8927.
for
the
The Principle Behind the Current-Sensing Feature
The most efficient way to sense the drain-source current is to
use the ratio-metric measurement. In a power MOSFET, it is
possible to implement this method easily.
The cell density, a favored term within the power MOSFET
industry, conveys that the power MOSFET structure consists
of many cells connected in parallel. In principle, these cells
constitute a resistive path for drain-source current. Electrically,
these cells are parallel connected resistors,
r
DS(on)
s
. Each cell
- being identical in structure and electrical characteristics -
shares the current equally when the device is on. This property
enables design of a MOSFET with a current-sensing feature.
Dividing the MOSFET cells in a known ratio creates two paths
that share the drain-source current. The path with the smaller
number of cells constitutes the sense current, which is much
smaller than the current conducting through the rest of the
cells. A very simple, low-power, external circuit can measure
this current. Multiplying this value with the cell ratio gives the
total drain-source current.
The classic Kelvin termination for the return of sense current
to the main source connection insures the measurement
accuracy. This terminal not only eliminates the ground loop,
but also minimizes the imbalance of internal structures with
two current paths.
The Current-Sensing Parameters, Table 1, and the
Current-Sense Die Characteristics and Schematic, Figure 2,
help to demonstrate the current-sensing operation and circuit
implementation.
TABLE 1: Current Sense Characteristics
Current Sensing Ratio
r
I
D
= 1 A, V
GSS
= 10 V, R
SENSE
= 1.1
420
520
620
Mirror Active Resistance
r
m(on)
V
GS
= 10 V, I
D
= 10 mA
3.5
相關PDF資料 |
PDF描述 |
|---|---|
| SI4736DY | Dual N-Channel 30-V (D-S) MOSFET with Schottky Diode |
| SI4750DY | Smart Power High-Side Switch |
| SI4750DY-E3 | Smart Power High-Side Switch |
| SI4750DY-T1-E3 | Smart Power High-Side Switch |
| SI4779CY | High-Side N-Channel Switch with Current Limit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI4730EY-E3 | 功能描述:MOSFET 30V 11.7A 3.6W RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| SI4730EY-T1-E3 | 功能描述:MOSFET 30 Volt 11.7A 3.6W RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| SI4731 | 制造商:SILABS 制造商全稱:SILABS 功能描述:Broadcast AM/FM Radio Receiver |
| Si4731-A10-GM | 功能描述:射頻接收器 Broadcast AM/FM Receiver w/ RDS/RBDS RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| Si4731-A-EVB | 功能描述:射頻開發工具 Si4731 Eval Board RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V |
發布緊急采購，3分鐘左右您將得到回復。