- 您現在的位置：買賣IC網 > PDF目錄9680 > SI4136-F-BT (Silicon Laboratories Inc)SYNTH WLAN SAT RADIO(RF1/RF2/IF) PDF資料下載
參數資料
| 型號： | SI4136-F-BT |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 9/34頁 |
| 文件大小： | 0K |
| 描述： | SYNTH WLAN SAT RADIO(RF1/RF2/IF) |
| 標準包裝： | 62 |
| 類型： | * |
| 驅動器/接收器數： | * |
| 規程： | * |
| 電源電壓： | 2.7 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Si4136/Si4126
Rev. 1.41
17
Table 6 summarizes the characteristics of the IF VCO.
Figure 14. Example of IF External Inductor
As
a
design
example,
suppose
synthesizing
frequencies in a 30 MHz band between 735 MHz and
765 MHz is desired. The center frequency should be
defined as midway between the two extremes, or
750 MHz. The PLL will be able to adjust the VCO output
frequency ±5% of the center frequency, or ±37.5 MHz of
750 MHz
(i.e.,
from
approximately
713 MHz
to
788 MHz). The IF VCO has a CNOM of 6.5 pF, and a
6.9 nH inductance (correct to two digits) in parallel with
this capacitance will yield the desired center frequency.
An external inductance of 4.8 nH should be connected
between IFLA and IFLB, as shown in Figure 14. This, in
addition to 2.1 nH of package inductance, will present
the
correct
total
inductance
to
the
VCO.
In
manufacturing, the external inductance can vary ±10%
of its nominal value and the Si4136 will correct for the
variation with the self-tuning algorithm.
For more information on designing the external trace
inductor, please refer to Application Note 31.
2.3. Self-Tuning Algorithm
The
self-tuning
algorithm
is
initiated
immediately
following power-up of a PLL or, if the PLL is already
powered, following a change in its programmed output
frequency. This algorithm attempts to tune the VCO so
that its free-running frequency is near the desired output
frequency. In so doing, the algorithm will compensate
for manufacturing tolerance errors in the value of the
external inductance connected to the IF VCO. It will also
reduce the frequency error for which the PLL must
correct to get the precise desired output frequency. The
self-tuning algorithm will leave the VCO oscillating at a
frequency in error by somewhat less than 1% of the
desired output frequency.
After self-tuning, the PLL controls the VCO oscillation
frequency. The PLL will complete frequency locking,
eliminating any remaining frequency error. Thereafter, it
will maintain frequency-lock, compensating for effects
caused by temperature and supply voltage variations.
The Si4136’s self-tuning algorithm will compensate for
component value errors at any temperature within the
specified temperature range. However, the ability of the
PLL to compensate for drift in component values that
occur
after
self-tuning
is
limited.
For
external
inductances with temperature coefficients around ±150
ppm/°C, the PLL will be able to maintain lock for
changes in temperature of approximately ±30°C.
Applications where the PLL is regularly powered-down
or the frequency is periodically reprogrammed minimize
or eliminate the potential effects of temperature drift
because the VCO is re-tuned in either case. In
applications where the ambient temperature can drift
substantially after self-tuning, it may be necessary to
monitor the lock-detect bar (LDETB) signal on the
AUXOUT pin to determine whether a PLL is about to
run out of locking capability. (See “2.9. Auxiliary Output
(AUXOUT)” for how to select LDETB.) The LDETB
signal will be low after self-tuning has completed but will
rise when either the IF or RF PLL nears the limit of its
compensation range. (LDETB will also be high when
either PLL is executing the self-tuning algorithm.) The
output frequency will still be locked when LDETB goes
high, but the PLL will eventually lose lock if the
temperature continues to drift in the same direction.
Therefore, if LDETB goes high both the IF and RF PLLs
should promptly be re-tuned by initiating the self-tuning
algorithm.
2.4. Output Frequencies
The IF and RF output frequencies are set by
programming the R- and N-Divider registers. Each PLL
has its own R and N registers so that each can be
Table 6. Si4136-BT/GT VCO Characteristics
VCO
Fcen Range
(MHz)
Cnom
(pF)
Lpkg
(nH)
Lext Range
(nH)
Min
Max
Min
Max
IF
526
952
6.5
2.1
2.2
12.0
f
CEN
1
2
L
TOT
C
NOM
---------------------------------------------
1
2
L
PKG
L
EXT
+
C
NOM
----------------------------------------------------------------------
==
Si4136
L
PKG
2
L
PKG
2
L
EXT
IFLB
IFLA
相關PDF資料 |
PDF描述 |
|---|---|
| MK1491-09FILN | IC CLK SRC AMD GEODE GX2 28SSOP |
| V300B24M150BF | CONVERTER MOD DC/DC 24V 150W |
| D38999/24FH53PB | CONN RCPT 53POS JAM NUT W/PINS |
| V300B24M150B3 | CONVERTER MOD DC/DC 24V 150W |
| ICS557GI-05ALF | IC CLK SOURCE QUAD PCI 20-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI4136-F-GM | 功能描述:射頻無線雜項 WLAN SATELITE RADIO MLP-28 RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| SI4136-F-GMR | 功能描述:時鐘發生器及支持產品 WLAN Satellite Radio Synthesizer RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| SI4136-F-GT | 功能描述:射頻無線雜項 WLAN SATELITE RADIO TSSOP-24 RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| SI4136-F-GTR | 功能描述:射頻無線雜項 WLAN Satellite Radio Synthesizer RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| SI4136M-EVB | 功能描述:開發板和工具包 - 無線 802.11b and ISM Band RoHS:否 制造商:Arduino 產品:Evaluation Boards 工具用于評估:AT32UC3L 核心:AVR32 頻率: 接口類型:USB 工作電源電壓:5 V |
發布緊急采購，3分鐘左右您將得到回復。