- 您現在的位置：買賣IC網 > PDF目錄10999 > SI3230-E-FT (Silicon Laboratories Inc)IC SLIC PROG 1CH 38TSSOP PDF資料下載
參數資料
| 型號： | SI3230-E-FT |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 31/108頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SLIC PROG 1CH 38TSSOP |
| 標準包裝： | 50 |
| 系列： | ProSLIC® |
| 功能： | 用戶線路接口概念（SLIC） |
| 接口： | SPI |
| 電路數： | 1 |
| 電源電壓： | 3.13 V ~ 5.25 V |
| 電流 - 電源： | 88mA |
| 功率（瓦特）： | 700mW |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 38-TFSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 38-TSSOP |
| 包裝： | 管件 |
| 包括： | DTMF 生成和解碼，F(xiàn)SK 生成 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
Si3230
Preliminary Rev. 0.96
29
Not
Recommended
fo
r N
ew
esi
gn
s
2.3.4. Enhanced FSK Waveform Generation
Silicon revisions C and higher support enhanced FSK
generation capabilities, which can be enabled by setting
FSKEN = 1 (direct Register 108, bit 6) and REN = 1
(direct Register 32, bit 6). In this mode, the user can
define mark (1) and space (0) attributes once during
initialization by defining indirect registers 99–104. The
user need only indicate 0-to-1 and 1-to-0 transitions in
the information stream. By writing to FSKDAT (direct
Register 52), this mode applies a 24 kHz sample rate to
tone generator 1 to give additional resolution to timers
and frequency generation. Application Note 32 gives
detailed instructions on how to implement FSK in this
mode. Additionally, sample source code is available
from Silicon Laboratories upon request.
2.3.5. Tone Generator Interrupts
Both the active and inactive timers can generate their
own interrupt to signal “on/off” transitions to the
software. The timer interrupts for tone generator 1 can
be individually enabled by setting the O1AE and O1IE
bits (direct Register 21, bits 0 and 1, respectively).
Timer interrupts for tone generator two are O2AE and
O2IE (direct Register 21, bits 2 and 3, respectively). A
pending interrupt for each of the timers is determined by
reading the O1AP, O1IP, O2AP, and O2IP bits in the
Interrupt Status 1 register (direct Register 18, bits 0
through 3, respectively).
2.4. Ringing Generation
The ProSLIC provides fully programmable internal
balanced ringing with or without a dc offset to ring a
wide variety of terminal devices. All parameters
associated with ringing are software programmable:
ringing frequency, waveform, amplitude, dc offset, and
ringing cadence. Both sinusoidal and trapezoidal ringing
waveforms are supported, and the trapezoidal crest
factor is programmable. Ringing signals of up to 88 V
peak or more can be generated, enabling the ProSLIC
to drive a 5 REN (1380
+ 40 F) ringer load across
loop lengths of 2000 feet (160
) or more.
2.4.1. Ringing Architecture
The ringing generator architecture is nearly identical to
that of the tone generator. The sinusoid ringing
waveform is generated using an internal two-pole
resonance
oscillator
circuit
with
programmable
frequency and amplitude. However, since ringing
frequencies are very low compared to the audio band
signaling
frequencies,
the
ringing
waveform
is
generated at a 1 kHz rate instead of 8 kHz.
The ringing generator has two timers that function the
same as for the tone generator timers. They allow on/off
cadence settings up to 8 seconds on/ 8 seconds off. In
addition to controlling ringing cadence, these timers
control the transition into and out of the ringing state.
Table 26 summarizes the list of registers used for
ringing generation.
Note:
Tone generator 2 should not be enabled concurrently
with the ringing generator due to resource sharing
within the hardware.
Table 26. Registers for Ringing Generation
Parameter
Range/ Description
Register
Bits
Location
Ringing Waveform
Sine/Trapezoid
TSWS
Direct Register 34
Ringing Voltage Offset Enable
Enabled/
Disabled
RVO
Direct Register 34
Ringing Active Timer Enable
Enabled/
Disabled
RTAE
Direct Register 34
Ringing Inactive Timer Enable
Enabled/
Disabled
RTIE
Direct Register 34
Ringing Oscillator Enable
Enabled/
Disabled
ROE
Direct Register 34
Ringing Oscillator Active Timer
0 to 8 seconds
RAT[15:0]
Direct Registers 48 and 49
Ringing Oscillator Inactive Timer
0 to 8 seconds
RIT[15:0]
Direct Registers 50 and 51
Linefeed Control (Initiates Ringing State)
Ringing State = 100b
LF[2:0]
Direct Register 64
High Battery Voltage
0 to –94.5 V
VBATH[5:0]
Direct Register 74
Ringing dc voltage offset
0 to 94.5 V
ROFF[15:0]
Indirect Register 19
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2NX-IY-B1 | CONVERTER MOD DC/DC 5.2V 50W |
| MC9S08AC32MFUE | MCU 8BIT 32K FLASH 64-QFP |
| S9S08SG8E2MTJ | MCU 8KB FLASH 20-TSSOP |
| VE-2NX-IX-S | CONVERTER MOD DC/DC 5.2V 75W |
| VE-2NW-IY-B1 | CONVERTER MOD DC/DC 5.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3230-E-FTR | 功能描述:電信線路管理 IC Sngl-CH DTMF Decoder dc-dc cnvrtr RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3230-GT | 制造商:SILABS 制造商全稱:SILABS 功能描述:PROSLIC㈢ PROGRAMMABLE CMOS SLIC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3230-KT | 功能描述:電信線路管理 IC SINGLE CH SLIC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3230-KTR | 制造商:Silicon Laboratories Inc 功能描述: |
| SI3230M-E-FM | 功能描述:射頻無線雜項 Single-Channel SLIC RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。