參數資料
型號： SI3212
廠商： Electronic Theatre Controls, Inc.
元件分類： Codec
英文描述： PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION
中文描述： ProSLIC產品可編程的CMOS用戶接口/有振鈴編解碼器/電池電壓生成
文件頁數： 42/122頁
文件大?。?/td> 1950K
代理商： SI3212
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
Si3210/Si3211/Si3212
42
Preliminary Rev. 1.11
receive path.
An additional analog loopback (ALM1) takes the
digital stream at the output of the A/D converter and
feeds it back to the D/A converter. (See Figure 23.)
The signal path starts with the analog signal at the
input of the transmit path and ends with an analog
signal at the output of the receive path. This
loopback option allows the testing of the analog
signal processing circuitry of the Si3210 completely
independent from any activity in the DSP.
The full digital loopback tests almost all the circuitry
of both the transmit and receive paths. The analog
signal at the output of the receive path is fed back to
the input of the transmit path by way of the hybrid
filter path. (See Figure 23.) The signal path starts
with 8-bit PCM data input to the receive path and
ends with 8-bit PCM data at the output of the
transmit path. The user can bypass the companding
process and interface directly to the 16-bit data.
An additional digital loopback (DLM) takes the digital
stream at the input of the D/A converter in the
receive path and feeds it back to the transmit A/D
digital filter. The signal path starts with 8-bit PCM
data input to the receive path and ends with 8-bit
PCM data at the output of the transmit path. This
loopback option allows the testing of the digital
signal processing circuitry of the Si3210 completely
independent from any analog signal processing
activity.The user can bypass the companding
process and interface directly to the 16-bit data.
Two-Wire Impedance Matching
The ProSLIC provides on-chip programmable two-wire
impedance settings to meet a wide variety of worldwide
two-wire return loss requirements. The two-wire
impedance is programmed by loading one of the eight
available impedance values into the TISS[2:0] bits of the
Two-Wire Impedance Synthesis Control register (direct
Register 10). If direct Register 10 is not user-defined,
the default setting of 600
will be loaded into the TISS
register.
Real and complex two-wire impedances are realized by
internal feedback of a programmable amplifier (RAC) a
switched
capacitor
network
transconductance amplifier (G
m
). (See Figure 23.) RAC
creates the real portion and XAC creates the imaginary
portion of G
m
’s input. G
m
then creates a current that
models the desired impedance value to the subscriber
loop. The differential ac current is fed to the subscriber
loop via the ITIPP and IRINGP pins through an off-chip
current buffer (I
BUF
), which is implemented using
transistor Q1 and Q2 (see Figure on page 16). G
m
is
referenced to an off-chip resistor (R
15
).
(XAC)
and
a
The ProSLIC also provides a means to compensate for
degraded
subscriber
loop
excessive line capacitance (leakage). The CLC[1:0] bits
of direct Register 10 increase the ac signal magnitude
to compensate for the additional loss at the high end of
the audio frequency range. The default setting of
CLC[2:0] assumes no line capacitance.
Silicon revisions C and higher support the option to
remove the internal reference resistor used to
synthesize ac impedances for 600 + 2.16
μ
F and
900 + 2.16
μ
F settings so that an external resistor
reference may be used. This option is enabled by
setting ZSEXT = 1 (direct Register 108, bit 4).
conditions
involving
Clock Generation
The ProSLIC will generate the necessary internal clock
frequencies from the PCLK input. PCLK must be
synchronous to the 8 kHz FSYNC clock and run at one
of the following rates: 256 kHz, 512 kHz, 768 kHz,
1.024 MHz, 1.536 MHz, 2.048 MHz, 4.096 MHz or
8.192 MHz. The ratio of the PCLK rate to the FSYNC
rate is determined via a counter clocked by PCLK. The
three-bit ratio information is automatically transferred
into an internal register, PLL_MULT, following a reset of
the ProSLIC. The PLL_MULT is used to control the
internal PLL which multiplies PCLK as needed to
generate 16.384 MHz rate needed to run the internal
filters and other circuitry.
The PLL clock synthesizer settles very quickly following
power up. However, the settling time depends on the
PCLK frequency and it can be approximately predicted
by the following equation:
Interrupt Logic
The ProSLIC is capable of generating interrupts for the
following events:
Loop current/ring ground detected
Ring trip detected
Power alarm
DTMF digit detected (Si3210 and Si3211 only)
Active timer 1 expired
Inactive timer 1 expired
Active timer 2 expired
Inactive timer 2 expired
Ringing active timer expired
Ringing inactive timer expired
Pulse metering active timer expired
Pulse metering inactive timer expired
T
SETTLE
F
PCLK
----------------
=
相關PDF資料
PDF描述
SI3212-BT PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION
SI3212-KT PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION
SI3311-H SI3311-H
SI3317-H IRED
SI3317-H(B) IRED
相關代理商/技術參數
參數描述
SI3212-BT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION
SI3212-KT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION
SI3215 制造商:SILABS 制造商全稱:SILABS 功能描述:PROSLIC㈢ PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION
SI3215-B-FM 功能描述:電信線路管理 IC SINGLE CHANNEL SLIC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI3215-B-FMR 制造商:Silicon Laboratories Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*