- 您現在的位置：買賣IC網 > PDF目錄373395 > SI3212-BT (Electronic Theatre Controls, Inc.) PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION PDF資料下載
參數資料
| 型號： | SI3212-BT |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | Codec |
| 英文描述： | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| 中文描述： | ProSLIC產品可編程的CMOS用戶接口/有振鈴編解碼器/電池電壓生成 |
| 文件頁數： | 27/122頁 |
| 文件大小： | 1950K |
| 代理商： | SI3212-BT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
Si3210/Si3211/Si3212
Preliminary Rev. 1.11
27
An internal calibration algorithm corrects for internal and
external component errors. The calibration is initiated by
setting the CAL bit in direct Register 96. Upon
completion of the calibration cycle, this bit is
automatically reset.
It is recommended that a calibration be executed
following system power-up. Upon release of the chip
reset, the Si3210 will be in the open state. After
powering up the dc-dc converter and allowing it to settle
for time (t
settle
) the calibration can be initiated.
Additional calibrations may be performed, but only one
calibration should be necessary as long as the system
remains powered up.
During calibration, V
BAT
, V
TIP
, and V
RING
voltages are
controlled by the calibration engine to provide the
correct external voltage conditions for the algorithm.
Calibration should be performed in the on-hook state.
RING or TIP must not be connected to ground during
the calibration.
Battery Voltage Generation and Switching
The ProSLIC supports two modes of battery supply
operation. First, the Si3210 integrates a dc-dc converter
controller that dynamically regulates a single output
voltage. This mode eliminates the need to supply large
external battery voltages. Instead, it converts a single
positive input voltage into the real-time battery voltage
needed for any given state according to programmed
linefeed parameters. Second, the Si3211 and Si3212
support switching between high and low battery voltage
supplies, as would a traditional monolithic SLIC.
For single to low channel count applications, the Si3210
proves to be an economical choice, as the dc-dc
converter eliminates the need to design and build high-
voltage power supplies. For higher channel count
applications where centralized battery voltage supply is
economical, or for modular legacy systems where
battery voltage is already available, the Si3211 and
Si3212 are recommended.
DC-DC Converter General Description
(Si3210/Si3210M Only)
The dc-dc converter dynamically generates the large
negative voltages required to operate the linefeed
interface. The Si3210 acts as the controller for a buck-
boost dc-dc converter that converts a positive dc
voltage into the desired negative battery voltage. In
addition to eliminating external power supplies, this
allows the Si3210 to dynamically control the battery
voltage to the minimum required for any given mode of
operation.
Two different dc-dc circuit options are offered: a BJT/
inductor version and a MOSFET/transformer version.
Due to the differences on the driving circuits, there are
two different versions of the Si3210. The Si3210
supports the BJT/inductor circuit option, and the
Si3210M version supports the MOSFET solution. The
only difference between the two versions is the polarity
of the DCFF pin with respect to the DCDRV pin. For the
Si3210, DCDRV and DCFF are opposite polarity. For
the Si3210M, DCDRV and DCFF are the same polarity.
Table 25 summarizes these differences.
Extensive design guidance on each of these circuits can
be obtained from Application Note 45 (AN45) and from
an interactive dc-dc converter design spreadsheet. Both
of these documents are available on the Silicon
Laboratories website (www.silabs.com).
BJT/Inductor Circuit Option Using Si3210
The BJT/Inductor circuit option, as defined in Figure 9,
offers a flexible, low-cost solution. Depending on
selected L1 inductance value and the switching
frequency, the input voltage (V
DC
) can range from 5 V to
30 V. By nature of a dc-dc converter’s operation, peak
and average input currents can become large with small
input voltages. Consider this when selecting the
appropriate input voltage and power rating for the V
DC
power supply.
For this solution, a PNP power BJT (Q7) switches the
current flow through low ESR inductor L1. The Si3210
uses the DCDRV and DCFF pins to switch Q7 on and
off. DCDRV controls Q7 through NPN BJT Q8. DCFF is
ac coupled to Q7 through capacitor C10 to assist R16 in
turning off Q7. Therefore, DCFF must have opposite
polarity to DCDRV, and the Si3210 (not Si3210M) must
be used.
MOSFET/Transformer Circuit Option Using Si3210M
The MOSFET/transformer circuit option, as defined in
Figure 11, offers higher power efficiencies across a
larger input voltage range. Depending on the
transformers primary inductor value and the switching
frequency, the input voltage (V
DC
) can range from 3.3 V
to 35 V. Therefore, it is possible to power the entire
ProSLIC solution from a single 3.3 V or 5 V power
supply. By nature of a dc-dc converter’s operation, peak
Table 25. Si3210 and Si3210M Differences
Device
DCFF Signal
Polarity
= DCDRV
= DCDRV
DCPOL
Si3210
Si3210M
Notes:
1.
DCFF signal polarity with respect to DCDRV signal.
2.
Direct Register 93, bit 5; This is a read-only bit.
0
1
相關PDF資料 |
PDF描述 |
|---|---|
| SI3212-KT | PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3311-H | SI3311-H |
| SI3317-H | IRED |
| SI3317-H(B) | IRED |
| Si4112G-BT* | Hook-Up Wire; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Color:Black; Approval Bodies:UL, CSA; Approval Categories:UL AWM Style 1015, CSA Type TEW, JQA-F-, Passes VW-1 Flame Test; Conductor Material:Copper RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3212-KT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PROSLIC PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3215 | 制造商:SILABS 制造商全稱:SILABS 功能描述:PROSLIC㈢ PROGRAMMABLE CMOS SLIC/CODEC WITH RINGING/BATTERY VOLTAGE GENERATION |
| SI3215-B-FM | 功能描述:電信線路管理 IC SINGLE CHANNEL SLIC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3215-B-FMR | 制造商:Silicon Laboratories Inc 功能描述: |
| SI3215-B-GM | 功能描述:IC SLIC/CODEC 1CH 38QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:ProSLIC® 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
發布緊急采購，3分鐘左右您將得到回復。