- 您現在的位置：買賣IC網 > PDF目錄10999 > SI3200-G-FSR (Silicon Laboratories Inc)IC SLIC/CODEC 100V LINE 16SOIC PDF資料下載
參數資料
| 型號： | SI3200-G-FSR |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 38/112頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SLIC/CODEC 100V LINE 16SOIC |
| 標準包裝： | 2,500 |
| 系列： | ProSLIC® |
| 功能： | 用戶線路接口概念（SLIC），CODEC |
| 接口： | GCI，PCM，SPI |
| 電路數： | 2 |
| 電源電壓： | 3.3V，5V |
| 電流 - 電源： | 110µA |
| 功率（瓦特）： | 941mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm Width）裸露焊盤 |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 帶卷 (TR) |
| 包括： | 電池切換，BORSCHT 功能，DTMF 生成和解碼，F(xiàn)SK 音調生成，調制解調器和傳真音調檢測 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
Si3220/25 Si3200/02
Rev. 1.3
31
Not
Recommended
fo
r N
ew
D
esi
gn
s
3.2. Power Supply Sequencing
Note: This section applies to Si3200 revision E only.
To ensure proper operation, the following power
sequencing guidelines should be followed:
VDD should be allowed to reach its steady state
voltage at least 20 ms before VBATH is allowed to
begin to ramp to its desired voltage.
Transients and oscillations with a dv/dt above 10 V/
s on the VDD and VBATH supplies should always be
avoided.
The ramp-up time for VDD should be in the range of
2 ms to 20 ms. The ramp-up time for VBATH should
be in the range of 10 ms to 150 ms. Slower ramp-up
times are not recommended.
VBATL rail must never be more negative than the
VBATH rail during any part of the power supply ramp-
up.
The Si3200 revision E features an ESD clamp
protection circuit connected between the VDD and
VBATH rails. This clamp protects the Si3200 against
ESD damage when the device is being handled out-of-
circuit during manufacture. Precautions must be taken
in the VDD and VBATH system power supply design. At
power-up, the VDD and VBATH rails must ramp-up from
0 V to their respective target values in a linear fashion
and must not exhibit fast transients or oscillations which
could cause the ESD clamp to be activated for an
extended period of time resulting in damage to the
Si3200. The resistors shown as R20 through R23
together with capacitors C23, C24, C30 and C31 on
Figure 12 and R23 through R26 along with capacitors
C24, C25, C32 and C33 in Figure 13 provide some
measure of protection against in-circuit ESD clamp
activation by forming a filter time constant and by
providing current limiting action in case of momentary
clamp activation during power-up. These resistors and
capacitors must be included in the application circuit,
while ensuring that the VDD and VBATH system power
supplies are designed to exhibit start-up behavior that is
free of undesirable transients or oscillations. Once the
VDD and VBATH are in their steady state final values, the
ESD clamp has circuitry that prevents it from being
activated by transients slower than 10 V/s. In the
steady powered-up state, the VDD and VBATH rails must
therefore not exhibit transients resulting in a voltage
slew rate greater than 10 V/s.
3.3. DC Feed Characteristics
The Si3220 and Si3225 offer programmable constant-
voltage and constant-current operating regions as
illustrated in Figure 14. The constant voltage region
(defined
by
the
open-circuit
voltage,
VOC)
is
programmable from 0 to 63.3 V in 1 V steps. The
constant current region (defined by the loop current
limit, ILIM) is programmable from 18 to 45 mA in
0.87 mA steps. The Si3220 and Si3225 exhibit a
characteristic dc impedance of 640
or 320 during
active mode. (See "3.4. Adaptive Linefeed" on page 34).
The TIP-RING voltage (VOC) is offset from ground by a
programmable voltage (VCM) to provide sufficient
voltage
headroom
to
the
most
positive
terminal
(typically the TIP lead in normal polarity or the RING
lead in reverse polarity) for carrying audio signals. A
similar programmable voltage (VOV) is an offset
between the most negative terminal and the battery
supply rail for carrying audio signals. (See Figure 14.)
The user-supplied battery voltage must have sufficient
amplitude under all operating states to ensure sufficient
headroom. The Si3200/2 may be powered by a lower
secondary battery supply (VBATL) to reduce total power
dissipation when driving short-loop lengths.
Figure 14. DC Linefeed Overhead Voltages
(Forward State)
3.3.1. Calculating Overhead Voltages
The two programmable overhead voltages (VOV and
VCM) represent one portion of the total voltage between
normal operating conditions, these overhead voltages
are sufficiently low to maintain the desired TIP-RING
voltage (VOC). However, there are certain conditions
under which the user must exercise care in providing a
battery supply with enough amplitude to supply the
required TIP-RING voltage and enough margin to
accommodate these overhead voltages. The VCM
voltage is programmed for a given operating condition.
Therefore,
the
open-circuit
voltage
(VOC) varies
according to the required overhead voltage (VOV) and
the supplied battery voltage (VBAT). The user should
pay attention to the maximum VOV and VCM that might
be required for each operating state.
In the off-hook active state, sufficient VOC must be
maintained to correctly power the phone from the
Constant I Region
Constant V Region
V
CM
V
OC
V
OV
V
OV
R
LOOP
V
BATH
V
TIP
V
RING
V
BATL
Secondary V
BAT
Selected
V
Loop Closure Threshold
相關PDF資料 |
PDF描述 |
|---|---|
| SI3201-FS | IC LINEFEED INTRFC SI321X 16SOIC |
| VI-BNY-IY-B1 | CONVERTER MOD DC/DC 3.3V 33W |
| VI-27J-IY-F3 | CONVERTER MOD DC/DC 36V 50W |
| VI-27R-IY-F4 | CONVERTER MOD DC/DC 7.5V 50W |
| VI-210-IY-F3 | CONVERTER MOD DC/DC 5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Si3200-G-GS | 功能描述:射頻無線雜項 100 V Linefeed Inter IC unit price RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| SI3200-G-GSR | 功能描述:電信線路管理 IC 100 V Linefeed Interface RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3200-GS | 功能描述:射頻無線雜項 100 V Linefeed codec RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
| SI3200-GSR | 制造商:Silicon Laboratories Inc 功能描述: |
| Si3200-KS | 功能描述:電信線路管理 IC 100 V LINEFEED INTERFACE IC.CHIPSET RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。