參數資料
型號: SI-8400L
廠商: Sanken Electric Co.,Ltd.
英文描述: Separate Excitation Switching Type with Coil
中文描述: 開關式勵磁分離與線圈
文件頁數: 4/6頁
文件大小: 77K
代理商: SI-8400L
99
I
T
a
-P
D
Characteristics
I
SI-8500L application circuit
Terminal no.2 is for soft start. Connecting a capacitor to the terminal
enables the soft start function. See page 85 for the formulas to calcu-
late delay time and rise time. Output can be turned on and off by
using the soft start terminal. To stop output, set the soft start terminal
voltage to V
SSL
(0.2V typ.) or less. To switch the potential of the soft
start terminal, drive the open collector of the transistor. Since the
discharge current from C
3
flows to the ON/OFF control transistor, limit
the current for protection. The SS terminal is pulled up to the power
supply in the IC and no external voltage can be applied.
I
Caution
1. Allocation of Components
For the best operating environment, the ground should be a single ground line at the GND terminal (terminal 2 on the SI-8400L, terminal 3 on
the SI-8500L), and the wiring from C
1
and C
2
to ground should be as short as possible.
2. Capacitors C
1
and C
2
1) They must satisfy the breakdown voltage and allowable ripple current.
Exceeding the ratings of these capacitors or using them without derating shortens their service lives and may also cause abnormal
oscillation of the IC.
2) C
2
must be a low-impedance type capacitor to ensure minimum ripple voltage and stable switching operation.
3) C
3
(SI-8500L only) is a capacitor for soft start. When not using soft start, leave terminal 2 open. It is pulled up inside the IC.
3. Terminals LIN and NC in the connection diagram must be left unconnected to other circuits.
4. The IC's metalic heatsink is electrically floating. Do not connect it to GND or any other circuit.
5. Since the SI-8400L and 8500L series have an open-package construction, they can only be operated in specific environments. Verify the
operating environment and use the conditions indicated in the reliability data.
1.5
1.0
0.5
00
25
50
Ambient Temperature T
a
(
°
C)
P
D
75
100
SI-8400L
3.0
2.0
1.0
00
25
50
75
100
SI-8500L
Ambient Temperature T
a
(
°
C)
P
D
SI-8500L
SI-8500L
S.S.
2
S.S.
2
S.S.
C
3
C
3
2
V
O.
Soft start
Soft start +V
O
ON/OFF
SI-8500L
G
SI-8400L/8500L Series
V
O
:Output voltage
I
O
:Output current
ηχ
:Efficiency (%)
The efficiency depends on the input
voltage and the output current. Thus,
obtain the value from the efficiency
graph and substitute the percentage
in the formula above.
P
D
=V
O
I
O
100
ηχ
–1
相關PDF資料
PDF描述
SI-8503L Separate Excitation Switching Type with Coil
SI-8504L Separate Excitation Switching Type with Coil
SI-8505L Separate Excitation Switching Type with Coil
SI-8401 Separate Excitation Switching Type with Coil
SI-8405L Separate Excitation Switching Type with Coil
相關代理商/技術參數
參數描述
SI-8401 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Separate Excitation Switching Type with Coil
Si8401AA-B-IS 功能描述:隔離器接口集成電路 1.0 kV Bidirectional I2C Isolator 1.7MHz RoHS:否 制造商:Texas Instruments 通道數量:2 傳播延遲時間: 電源電壓-最大:5.5 V 電源電壓-最小:3 V 電源電流:3.6 mA 功率耗散: 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:SOIC-8 封裝:Tube
SI8401AA-B-ISR 功能描述:隔離器接口集成電路 1kV Bidirect I2C Iso 1.7MHz ADuM RoHS:否 制造商:Texas Instruments 通道數量:2 傳播延遲時間: 電源電壓-最大:5.5 V 電源電壓-最小:3 V 電源電流:3.6 mA 功率耗散: 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:SOIC-8 封裝:Tube
Si8401AB-B-IS 功能描述:隔離器接口集成電路 2.5 kV Bidirectional I2C Isolator 1.7MHz RoHS:否 制造商:Texas Instruments 通道數量:2 傳播延遲時間: 電源電壓-最大:5.5 V 電源電壓-最小:3 V 電源電流:3.6 mA 功率耗散: 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:SOIC-8 封裝:Tube
SI8401AB-B-ISR 功能描述:隔離器接口集成電路 2.5 kV Bidirect I2C Isolator 1.7MHz RoHS:否 制造商:Texas Instruments 通道數量:2 傳播延遲時間: 電源電壓-最大:5.5 V 電源電壓-最小:3 V 電源電流:3.6 mA 功率耗散: 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:SOIC-8 封裝:Tube