- 您現在的位置：買賣IC網 > PDF目錄365543 > SI-8120E (SANKEN ELECTRIC CO LTD) Full-Mold, Separate Excitation Switching Type PDF資料下載
參數資料
| 型號： | SI-8120E |
| 廠商： | SANKEN ELECTRIC CO LTD |
| 元件分類： | 穩壓器 |
| 英文描述： | Full-Mold, Separate Excitation Switching Type |
| 中文描述： | 0.61 A SWITCHING REGULATOR, 60 kHz SWITCHING FREQ-MAX, ZFM5 |
| 封裝： | TO-220, 5 PIN |
| 文件頁數： | 3/4頁 |
| 文件大小： | 41K |
| 代理商： | SI-8120E |
78
I
Block Diagram
I
Standard External Circuit
I
T
a
-P
D
Characteristics
SW
OUT
V
OS
V
IN
3
GND
5
N.C
4
2
1
OSC
Reg.
OCP
Comp.
Reset
Drive
TSD
Amp.
V
REF
V
IN
C
1
D
1
L
1
5V
: 200
μ
H
9V
,
12V: 300
μ
H
100
μ
F
V
IN
V
O
AK06
(Sanken)
GND
NC
GND
GND
SI-8000E
SW
OUT
V
OS
1
2
3
+
C2
330
μ
F
+
5
4
15
10
5
0
–30
0
25
50
Ambient Operating Temperature T
a
(
°
C)
P
D
75
100
125
20
×
20
×
2mm(.
°
CW
100
×
100
×
2mm(52
CW
75
×
75
×
2mm(76
°
CW
Infinite heatsink
Without heatsink
With Silicon Grease
Heatsink: Aluminum
G
SI-8000E Series
I
Selecting External Components
1. Inductor L
1
1) It must be suited for switching regulators.
Do not use inductors as noise filters as they generate excessive heat.
2) It must have the appropriate inductance value.
If the inductance is too small (150
μ
H or lower), abnormal oscillation may occur causing operation problems in the overcurrent protection
circuit within the rated current range.
3) The rated current must be satisfied.
If the rated current is exceeded, magnetic saturation leads to overcurrent.
2. Capacitors C
1
and C
2
1) They must satisfy the withstand voltage and allowable ripple current.
Exceeding the ratings of these capacitors or using them without derating shortens their service lives and may also cause abnormal
oscillation of the IC.
2) C
2
must be a low-impedance type capacitor.
A low-impedance type capacitor is recommended for C
2
to ensure minimum ripple voltage and stable switching operation.
3. Diode D
1
The Sanken AK06 diode is recommended for D
1
. If you intended to use an equivalent diode, be sure to use a Schottky Barrier diode and make
sure that the reverse voltage applied to terminal 2 of the IC does not exceed the value (–1V) given in the absolute maximum ratings. If you use
a fast recovery diode or any other diode, application of a reverse voltage generated from the recovery or ON voltage of the diode may damage
the IC.
Application
Variable output voltage
Output voltage can be adjusted in the same way as SI-8000S in page 85.
The efficiency depends on the input voltage and the out-
put current. Thus, obtain the value from the efficiency
graph on page 79 and substitute the percentage in the
formula above.
V
O
: Output voltage
V
IN
: Input voltage
I
O
: Output current
η
x : Efficiency (%)
V
F
: Diode forward voltage
0.4V(AK06)
Thermal design for D
1
must be considered separately.
P
D
=V
O
I
O
100 –1 –V
F
I
O
1– V
O
ηχ
V
IN
相關PDF資料 |
PDF描述 |
|---|---|
| SI-8000JF | RELAY PWR SPST 200ADC LEAD TERM |
| SI-8015JF | Full-Mold, Separate Excitation Switching Type |
| SI-8090JF | Full-Mold, Separate Excitation Switching Type |
| SI-8025JF | Full-Mold, Separate Excitation Switching Type |
| SI-8050JF | Full-Mold, Separate Excitation Switching Type |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI-8120JD | 制造商:ALLEGRO 功能描述:TR/ Regulator IC - Switching Mode (Surface mount) 制造商:Allegro MicroSystems LLC 功能描述:TR/ Regulator IC - Switching Mode (Surface mount) |
| SI-8120JD-TL | 制造商:Sanken Electric Co Ltd 功能描述:IC REG BUCK 12V 1.5A TO263-5 |
| SI-8120JF | 制造商:Sanken Electric Co Ltd 功能描述:IC REG BUCK 12V 1.5A TO220F-5 |
| SI-8120JF-LF1101 | 制造商:Sanken Electric Co Ltd 功能描述: |
| SI-8120S | 制造商:Sanken Electric Co Ltd 功能描述:IC REG BUCK 12V 3A TO-220F-5 制造商:ALLEGRO 功能描述:IC, LINEAR VOLT REG, 12V, TO-220-5, Primary Input Voltage:40V, Output Voltage Mi 制造商:Allegro MicroSystems LLC 功能描述:IC, LINEAR VOLT REG, 12V, TO-220-5, Primary Input Voltage:40V, Output Voltage Min:11.5V, Output Voltage Max:12.5V, Output Voltage Fixed:12V, No. of Pins:5, No. of Outputs:1, Output Current:3A, Operating Temperature Min:-30C, MSL:- |
發布緊急采購，3分鐘左右您將得到回復。