- 您現在的位置：買賣IC網 > PDF目錄365543 > SI-8000S (Sanken Electric Co.,Ltd.) Full-Mold, Separate Excitation Switching Type PDF資料下載
參數資料
| 型號： | SI-8000S |
| 廠商： | Sanken Electric Co.,Ltd. |
| 英文描述： | Full-Mold, Separate Excitation Switching Type |
| 中文描述： | 全模具，獨立開關式勵磁 |
| 文件頁數： | 5/6頁 |
| 文件大小： | 63K |
| 代理商： | SI-8000S |
84
Caution
1. Selecting External Components
(1) Choke coil L
1
To maintain the stable operation of the regulator, choke coil L
1
should be selected appropriately.
When selecting choke coil L
1
, consider the following:
a) Suitable for a switching regulator
Do not use a coil as a noise filter because it generates excess
heat.
b) Appropriate inductance
The greater the inductance of the choke coil, the smaller the
output ripple voltage. However, the size of the coil increases
large as the inductance increases. If the inductance is low, a
greater peak current flows to the IC and loss increases. This
is not favorable for stable operation.
The standard external circuit shows reference inductance val-
ues suitable for stable operation. However, the appropriate
inductance may also be calculated as follows:
L= (V
IN
–V
O
)V
O
ILV
IN
f
Where, deltaIL indicates the ripple current of the choke coil
that is roughly set as follows:
If the working output current is close to the maximum rating
(3 A) of SI-8000S
Ripple current = output current
×
0.2 to 0.3
If the working output current is about 1.0A or less
Ripple current = output current
×
0.3 to 0.4
c) Satisfying the rated current
The rated current of a choke coil must be greater than the
maximum load current. Note that the inductance decreases
drastically and an excess current flows if the load current ex-
ceeds the rated current of the coil.
d) Good DC current superposition characteristics
The current flowing through a choke coil is a triangular wave-
form current superimposed on a DC current equal to the load
current. The coil inductance decreases as the load current
increases. In general, the coil can be used until the induc-
tance drops to 50% of the rated value. Use this as the refer-
ence value for selection.
100%
50%
I
O
(max.)
Inductance
Load current
e) Less noise
A drum-type open magnetic core coil can affect peripheral
circuits with noise because the flux passes outside the coil.
To avoid this problem, use a toroidal, EI, or EE type open
magnetic core coil.
G
SI-8000S Series
(2) Input capacitor C
1
Input capacitor C
1
operates as a bypass capacitor in the input
circuit.
When selecting input capacitor C
1
, consider the following:
a) The breakdown voltage is higher than the maximum input volt-
age.
b) Satisfies the allowable ripple current
Exceeding the ratings of this capacitor or using it without de-
rating may reduce its service life and also cause the regulator
to malfunction. Therefore, an input capacitor with a sufficient
margin should be selected. With the SI-8000S Series, the
effective ripple current Irms flowing to the input capacitor can
be calculated approximately as follows:
1.2
×
V
O
V
IN
I
rms
×
I
O
(3) Output capacitor C
2
Output capacitor C
2
operates as a smoothing capacitor for switch-
ing output. The output ripple voltage from the regulator is deter-
mined by the product of the pulsating current part
IL (=C
2
charge-
discharge current) of the choke coil current and the equivalent
series resistance ESR of the output capacitor C
2
.
V
rip
=
ILC2ESR
Therefore, a capacitor of low equivalent series resistance ESR
should be selected to reduce the output ripple voltage. It is rec-
ommended to select a low-impedance capacitor intended for use
with switching regulators as C
2
.
(4) Diode D
1
Use a Schottky barrier diode for D
1
. If you use a general rectifier
diode or fast recovery diode, the IC may be damaged. (Sanken
RK46 recommended)
2. Notes on Pattern Design
(1) Large current line
Since a large current flows through the bold lines in the standard
external circuit make the pattern as wide and as short as pos-
sible.
2
1
3
4
SI-8000S
V
IN
GND
C
1
C
2
L
1
D
1
V
OUT
GND
+
+
(2) Input capacitor
Place the input capacitor C
1
and output capacitor C
2
as close to
the IC as possible. Since a large current flows through the lead
wires of the input and output capacitors to charge and discharge
them quickly, minimize the lead wire length. The pattern around
the capacitors should also be minimized.
C
1
. C
2
.
C
1
. C
2
.
+
+
Example of bad pattern
Example of good pattern
相關PDF資料 |
PDF描述 |
|---|---|
| SI-8090S | Full-Mold, Separate Excitation Switching Type |
| SI-8033 | Full-Mold, Separate Excitation Switching Type |
| SI-8033S | Full-Mold, Separate Excitation Switching Type |
| SI-8120S | Full-Mold, Separate Excitation Switching Type |
| SI-8150S | Full-Mold, Separate Excitation Switching Type |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI-8000S_10 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Full-Mold, Separate Excitation Step-down Switching Mode Regulator ICs |
| SI-8000S_11 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Full-Mold, Separate Excitation Step-down Switching Mode |
| SI-8000SD | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface Mount, Separate Excitation Step-down Switching Mode Regulator ICs |
| SI-8000SD_10 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface Mount, Separate Excitation Step-down Switching Mode Regulator ICs |
| SI-8000SD_11 | 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface Mount, Separate Excitation Step-down Switching Mode |
發布緊急采購，3分鐘左右您將得到回復。