- 您現在的位置：買賣IC網 > PDF目錄372142 > SG883B 1.5 AMP THREE TERMINAL ADJUSTABLE VOLTAGE REGULATOR PDF資料下載
參數資料
| 型號： | SG883B |
| 英文描述： | 1.5 AMP THREE TERMINAL ADJUSTABLE VOLTAGE REGULATOR |
| 中文描述： | 1.5放大器三端可調穩壓器 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 264K |
| 代理商： | SG883B |
SG117A/SG117 SERIES
2/93 Rev 1.
2 10/02
Copyright
1994
L
IN
F
IN
ITY
Microelectronics Inc.
11861 Western Avenue
∞
Garden Grove, CA 92841
(714) 898-8121
∞
FAX: (714) 893-2570
7
APPLICATION INFORMATION
(continued)
BYPASS CAPACITORS
Input bypassing using a 1μF tantalum or 25μF electrolytic is
recommended when the input filter capacitors are more than 5
inches from the device. A 0.1
μ
F bypass capacitor on the
ADJUST pin is required if the load current varies by more than 1A/
μ
sec. Improved ripple rejection (80dB) can be accomplished by
adding a 10μF capacitor from the adjust pin to ground. For
improved AC transient response and to prevent the possibility of
oscillation due to unknown reactive load, a 1μF capacitor is also
recommended at the output. Because of their low impedance at
high frequencies, the best type of capacitor to use is solid
tantalum.
FIGURE 22 - 5V REGULATOR WITH SHUT DOWN
FIGURE 23 - 21V PROGRAMMING SUPPLY FOR UV PROM/EEPROM
FIGURE 24 - 2816 EEPROM SUPPLY PROGRAMMER FOR READ/WRITE CONTROL
FIGURE 25 - TEMPERATURE COMPENSATED LEAD ACID BATTERY CHARGER
FIGURE 21 - IMPROVING RIPPLE REJECTION
LOAD REGULATION
Because the SG117A is a three-terminal device, it is not possible
to provide true remote load sensing. Load regulation will be
limited by the resistance of the wire connecting the regulator to
the load. For the data sheet specification, regulation is measured
at the bottom of the package. Negative side sensing is a true
Kelvin connection, with the bottom of the output divider returned
to the negative side of the load. Although it may not be immedi-
ately obvious, best load regulation is obtained when the top of the
divider is connected directly to the case, not to the load. This is
illustrated in Figure 18. If R
were connected to the load, the
effective resistance between the regulator and the load would be
( )
Connected as shown, R
is not multiplied by the divider ratio. R
P
is about 0.004
per foot using 16 gauge wire. This translates to
4mV/ft. at 1A load current, so it is important to keep the positive
lead between regulator and load as short as possible.
FIGURE 20 - REMOTE SENSING
R
P
X
,
R
P
= Parasitic Line Resistance.
2
1
相關PDF資料 |
PDF描述 |
|---|---|
| SGDESC | 1.5 AMP THREE TERMINAL ADJUSTABLE VOLTAGE REGULATOR |
| SG117AIG | 1.5 AMP THREE TERMINAL ADJUSTABLE VOLTAGE REGULATOR |
| SG117AK | 1.5 AMP THREE TERMINAL ADJUSTABLE VOLTAGE REGULATOR |
| SG117AL | 1.5 AMP THREE TERMINAL ADJUSTABLE VOLTAGE REGULATOR |
| SG117AR | 1.5 AMP THREE TERMINAL ADJUSTABLE VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SG89 | 制造商:Ametherm Inc 功能描述: |
| SG-890A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SURFCOIL? SMT INDUCTORS AND TRANSFORMERS (PROFESSIONAL GRADE) |
| SG8P1533C019 | 制造商:Texas Instruments 功能描述: |
| SG8SC4M | 制造商:SHINDENGEN 制造商全稱:Shindengen Electric Mfg.Co.Ltd 功能描述:Schottky Barrier Diode |
| SG8SC4M-5600 | 功能描述:肖特基二極管與整流器 Schottky Barrier Diode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。