- 您現在的位置：買賣IC網 > PDF目錄271662 > SDC-14615T-452Q (DATA DEVICE CORP) SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, DIP36 PDF資料下載
參數資料
| 型號： | SDC-14615T-452Q |
| 廠商： | DATA DEVICE CORP |
| 元件分類： | 位置變換器 |
| 英文描述： | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, DIP36 |
| 封裝： | 1.700 X 0.780 INCH, 0.210 INCH HEIGHT, DDIP-36 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 358K |
| 代理商： | SDC-14615T-452Q |
4
BIT, BUILT-IN-TEST (OPTIONAL)
This output is a logic line that will flag an internal fault condition,
or LOS (Loss-Of-Signal). The internal fault detector monitors the
internal error and, when it exceeds ±100 LSBs, will set the line
to a logic 0; this condition will occur during a large-step input and
will reset to a logic 1 after the converter settles out. (The error
voltage is filtered with a 500 s filter) BIT will set for an overve-
locity condition because the converter loop can’t maintain
input/output sync. BIT will also be set if a total LOS (loss of all
signals) occurs.
NO FALSE 180° HANGUP
This feature eliminates the “false 180° reading” during instanta-
neous 180° step changes; this condition most often occurs when
the input is “electronically switched” from a digital-to-synchro
converter. If the “MSB” (or 180° bit) is “toggled” on and off, a con-
verter without the “false 180° reading” feature may fail to
respond.
The condition is artificial, as a “real” synchro or resolver cannot
change its output 180° instantaneously. The condition is most
often noticed during wraparound verification tests, simulations,
or troubleshooting.
,
ENABLE
150 ns MAX
DATA
VALID
100 ns MAX
HIGH Z
,,,,,,
DATA
VALID
500 ns MAX
INHIBIT
1.895 ±0.005
(48.1 ±0.13)
1.700 ±0.005
(43.2 ±0.13)
0.018 (0.46)
DIAM TYP
0.100 TYP(2.54)
TOL. NON-
CUMULATIVE
0.21 MAX
(5.3)
DOT
IDENTIFIES
PIN 1
0.775 ±0.005
(19.7 ±0.13)
0.600 ±0.005
(15.2 ±0.13)
0.09 ±0.01
(2.3 ±0.25)
0.10 ±0.01
(2.5 ±0.3)
SIDE VIEW
BOTTOM VIEW
0.25 MIN
(6.4)
0.015 MAX
(0.39)
SEATING
PLANE
0.055 (1.4)
RAD TYP
0.086 TYP
RADIUS
TABLE 2. PINOUTS (36 PIN) (SEE NOTE 1)
1 S1A(S)
S1A(R)
N.C.
36
2 S2A(S)
S2A(R)
+COSA(D) 36 EM-A (Enable MSBs)
3 S3A(S)
S3A(R)
+SINA(D)
34 EL-A (Enable LSBs)
4 N.C.
S4A(R)
N.C.
33 INH (Inhibit)
5 GND
(Ground)(see Note 4)
32
6
AGND
(Analog Ground)
(see Note 4)
31 EM-B (Enable MSBs)
7 S1B(S)
S1B(R)
N.C.
30 EL-B (Enable LSBs)
8 S2B(S)
S2B(R)
+COSB(D) 29 Bit 8/Bit 16 (see Note 3)
9 S3B(S)
S3B(R)
+SINB(D)
28 Bit 7/Bit 15 (see Note 3)
10 N.C.
S4B(R)
N.C.
27 Bit 6/Bit 14
11 -5 V (Power Supply)
26 Bit 5/Bit 13
12 +5 V (Power Supply)
25 Bit 4/Bit 12
13 S1C(S)
S1C(R)
N.C.
24 Bit 3/Bit 11
14 S2C(S)
S2C(R)
+COSC(D) 23 Bit 2/Bit 10
15 S3C(S)
S3C(R)
+SINC(D)
22 Bit 1/Bit 9
16 N.C.
S4C(R)
N.C.
21
17 -REF (-Reference Input)
20 EL-C (Enable LSBs)
18 +REF (+Reference Input)
19 EM-C (Enable MSBs)
FIGURE 3. INHIBIT TIMING
FIGURE 4. ENABLE TIMING
Notes:
1. Dimensions are in inches (millimeters).
2. Lead identification numbers are for reference only.
3. Lead clusters shall be centered within ±0.01 of outline dimensions. Lead spac-
ing dimensions apply only at seating plane.
4. Pin material meets solderability requirements to MIL-STD-202E, Method 208C.
5. Case is electrically floating.
FIGURE 5. SDC-14610/15 MECHANICAL OUTLINE
Notes: 1. (S) = Synchro; (R) = Resolver; (D) = 2 V Resolver Direct
2. Replaced with BIT - “T” option
3. SDC-14615 Series only
4. Connect pin 5 (GND) to pin 6 (AGND) close to the hybrid
VEL A (Velocity Output)
(see Note 2)
VEL B (Velocity Output)
(see Note 2)
VEL C (Velocity Output)
(see Note 2)
相關PDF資料 |
PDF描述 |
|---|---|
| SD-14550FX-362W | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDMA34 |
| SD-14590D3-844Q | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, MDIP36 |
| SDC-14585-322W | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, DIP36 |
| SD-14597F1-804Z | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36 |
| SD-14597F1-805Z | SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SDC15 | 制造商:Semtech Corporation 功能描述:DIODE TVS DUAL BIDIR 12V SOT-23 制造商:Semtech Corporation 功能描述:DIODE, TVS, DUAL, BIDIR, 12V, SOT-23 制造商:Semtech Corporation 功能描述:DIODE, TVS, DUAL, BIDIR, 12V, SOT-23; Clamping Voltage Vc Max:21.2V; Diode Case Style:SOT-23; No. of Pins:3 ;RoHS Compliant: Yes |
| SDC15.TC | 制造商:Semtech Corporation 功能描述:ESD Suppressor TVS ±15KV 3-Pin SOT-23 T/R |
| SDC15.TCT | 功能描述:IC TVS BI-DIR 12V 300W SOT-23 RoHS:是 類別:過電壓，電流，溫度裝置 >> TVS - 二極管 系列:- 產品目錄繪圖:SMB 600 Watt Top SMB 600 Watt Side 1 SMB 600 Watt Side 2 標準包裝:10 系列:- 電壓 - 反向隔離（標準值）:25.6V 電壓 - 擊穿:28.5V 功率（瓦特）:600W 電極標記:單向 安裝類型:表面貼裝 封裝/外殼:DO-214AA，SMB 供應商設備封裝:SMB 包裝:剪切帶 (CT) 產品目錄頁面:2386 (CN2011-ZH PDF) 其它名稱:P6SMB30AT3GOSCT |
| SDC15.TCT-CUT TAPE | 制造商:SEMTECH 功能描述:SDC Series 21.2 V 120 pF Uni-Directional Surface Mount TVS Diode Array - SOT-23 |
| SDC15_04 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:TVS Diode Array for ESD Protection of 12V Data and Power Lines |
發布緊急采購，3分鐘左右您將得到回復。