參數資料
      型號: SD-14596F2-242S
      廠商: DATA DEVICE CORP
      元件分類: 位置變換器
      英文描述: SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36
      封裝: CERAMIC, FP-36
      文件頁數: 10/14頁
      文件大?。?/td> 416K
      代理商: SD-14596F2-242S
      5
      SOLID-STATE BUFFER INPUT PROTECTION — TRANSIENT
      VOLTAGE SUPPRESSION
      The solid-state signal and reference inputs are true differential
      inputs with high ac and dc common rejection, so most applica-
      tions will not require units with isolation transformers. Input
      impedance is maintained with power off. The recurrent ac peak +
      dc common mode voltage should not exceed the values in
      TABLE 2.
      REFERENCE
      OSCILLATOR
      PARALLEL
      DATA
      SD-14595/96/97
      STATOR
      ROTOR
      S3
      S1
      S2
      S1
      S3
      LBE
      HBE
      R2
      R1
      LO
      HI
      RH
      VEL (VELOCITY)
      INH (INHIBIT)
      CB (COUNT)
      RL
      S4
      REFERENCE
      OSCILLATOR
      PARALLEL
      DATA
      STATOR
      ROTOR
      S3
      S1
      S2
      S1
      S3
      LBE
      HBE
      R4
      R2
      LO
      HI
      RH
      VEL (VELOCITY)
      INH (INHIBIT)
      CB (COUNT)
      RL
      S4
      RD-14595/96/97
      FIGURE 4. SYNCHRO INPUT CONNECTION DIAGRAM
      FIGURE 5. RESOLVER INPUT CONNECTION DIAGRAM
      90 V line-to-line systems may have voltage transients which
      exceed the 500 V specification listed.
      These transients can
      destroy the thin-film input resistor network in the hybrid.
      Therefore, 90 V L-L solid-state input modules may be protected
      by installing voltage suppressors as shown. Voltage transients
      are likely to occur whenever synchro or resolver are switched on
      and off. For instance a 1000 V transient can be generated when
      the primary of a CX or TX driving a synchro or resolver input is
      opened. See FIGURE 6.
      INTERFACING - DIGITAL OUTPUTS AND CONTROLS
      DIGITAL INTERFACE
      The digital interface circuitry performs three main functions:
      1. Latches the output bits during an Inhibit (INH) command allow-
      ing stable data to be read out of the SD-14595/96/97.
      2. Furnishes parallel tri-state data formats.
      3. Acts as a buffer between the internal CMOS logic and the
      external TTL logic.
      In the SD-14595/96/97, applying an Inhibit (INH) command will
      lock the data in the inhibit transparent latch without interfering
      with the continuous tracking of the converter’s feedback loop.
      Therefore the digital angle
      φ is always updated and the INH can
      be applied for an arbitrary amount of time. The Inhibit
      Transparent Latch and the 50 ns delay are part of the inhibit cir-
      cuitry. For further information see the INHIBIT (INH, PIN 13)
      paragraph.
      HYBRID
      S3
      S2
      S1
      RH
      RL
      CR1
      CR2
      S1
      FOR 90 V SYNCHRO INPUTS
      1N6071A
      CR3
      S2
      S3
      CR1, CR2, and CR3 are 1N6136A, bipolar transient voltage suppressors
      or equivalent.
      HYBRID
      S3
      S2
      S1
      S4
      FOR 90 V RESOLVER INPUTS
      CR4
      CR5
      S3
      S2
      S1
      S4
      90 V L-L
      RESOLVER
      INPUT
      CR4 and CR5 are 1N6136A, bipolar transient voltage suppressors or equivalent.
      FIGURE 6. CONNECTIONS FOR VOLTAGE
      TRANSIENT SUPPRESSORS
      COMMON MODE
      MAXIMUM
      100 V
      30 V Peak
      180 V Peak
      250 V Peak
      150 V
      11.8 VL-L
      90 VL-L
      Reference
      MAX TRANSIENT PEAK
      VOLTAGE
      1 VL-L
      INPUT
      TABLE 2.
      相關PDF資料
      PDF描述
      SD-14596F2-242W SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36
      SD-14596F2-242Y SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36
      SD-14596F2-244Q SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36
      SD-14596F2-244Y SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36
      SD-14596F2-244 SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDFP36
      相關代理商/技術參數
      參數描述
      SD-14596F2-302 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Synchro-to-Digital Converter
      SD-14596F2-304 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Synchro-to-Digital Converter
      SD-14596F3-102 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Synchro-to-Digital Converter
      SD-14596F3-104 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Synchro-to-Digital Converter
      SD-14596F3-112 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Synchro-to-Digital Converter