<li id="0pa5k"><wbr id="0pa5k"></wbr></li>
  • 參數資料
    型號: SD-14531D3-244Q
    廠商: DATA DEVICE CORP
    元件分類: 位置變換器
    英文描述: SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, MDMA36
    封裝: KOVAR, DDIP-36
    文件頁數: 16/16頁
    文件大?。?/td> 170K
    代理商: SD-14531D3-244Q
    9
    Data Device Corporation
    www.ddc-web.com
    SD-14531
    SD-14531
    8 BIT BUS
    (MSB) BIT 1
    BIT 2
    BIT 3
    BIT 4
    BIT 5
    BIT 6
    BIT 7
    BIT 8
    BIT 9
    BIT 10
    BIT 11
    BIT 12
    BIT 13
    BIT 14
    BIT 15
    (LSB) BIT 16
    D7
    D6
    D5
    D4
    D3
    D2
    D1
    D0
    HBE
    LBE
    INH
    DATA 1-8
    VALID
    DATA 9-16
    VALID
    500 ns MIN
    150 ns MIN
    100 ns MAX
    150 ns MIN
    100 ns MAX
    LBE
    HBE
    FIGURE 11. 8-BIT DATA TRANSFER
    FIGURE 12. 8-BIT DATA TRANSFER TIMING
    Note: For further understanding refer to the beginning of this sec-
    tion (i.e., Digital Interface, Digital Angle Outputs, Digital Angle
    Output Timing, and Inhibit).
    DATA TRANSFER TO 16-BIT BUS
    Data transfer to the 16-bit bus is much simpler than the 8-bit bus.
    FIGURES 13 and 14 show the connections and timing for trans-
    ferring data from the SD-14531 to a 16-bit bus.
    As can be seen by the timing diagram the following occurs:
    1. The converter INH control is applied and must remain low for
    a minimum of 500 ns before valid data is transferred.
    2. HBE and LBE are set to a low state (logic 0) 350 ns minimum
    after INH goes low and must remain low for a minimum of 150 ns
    before the data (1-16) is valid and transferred.
    3. HBE and LBE should go high (to logic 1) at least 100 ns MAX
    before another device uses the bus.
    4. INH goes high and data transfer is done and the data refresh
    cycle can begin. Note the time it takes for INH to go to a logic 1
    should be 100 ns minimum before valid data is transferred.
    Note: For further understanding refer to the beginning of this sec-
    tion (i.e., Digital Interface, Digital Angle Outputs, Digital Angle
    Output Timing, and Inhibit).
    INTERFACING - ANALOG OUTPUTS
    The analog outputs are AC error (e), Analog Return (V), and
    Velocity (VEL).
    AC ERROR (e, PIN 12)
    The AC error is proportional to the difference between the input
    angle
    θ and the digital input angle φ, (θ-φ), with a scaling of:
    3.5 mV rms/LSB (14-bit mode)
    1.75 mV rms/LSB (16-bit mode)
    The e output can swing ±3 V min with respect to Analog Return (V).
    ANALOG RETURN (V, PIN 11)
    This internal voltage is not required externally for normal opera-
    tion of the converter. It is used as the internal DC reference and
    the return for the VEL and e outputs. It is nominally +4.3 V and is
    proportional to the +5 V DC supply.
    VELOCITY (VEL, PIN 10)
    The velocity output (VEL, pin 10) is a DC voltage proportional to
    angular velocity d
    θ/dt. The velocity is the input to the voltage-
    controlled oscillator (VCO), as shown in FIGURE 1. Its linearity
    相關PDF資料
    PDF描述
    SD-14531F1-345Z SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDMA36
    SD-14531D3-252Q SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, MDMA36
    SD-14531F1-375L SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDMA36
    SD-14531F1-415K SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDMA36
    SD-14531F1-422Y SYNCHRO OR RESOLVER TO DIGITAL CONVERTER, CDMA36
    相關代理商/技術參數
    參數描述
    SD1455 功能描述:射頻雙極電源晶體管 NPN 25V 170-230MHz RoHS:否 制造商:M/A-COM Technology Solutions 配置:Single 直流集電極/Base Gain hfe Min:40 最大工作頻率:30 MHz 集電極—發射極最大電壓 VCEO:25 V 發射極 - 基極電壓 VEBO:4 V 集電極連續電流:20 A 最大直流電集電極電流: 功率耗散:250 W 封裝 / 箱體:Case 211-11 封裝:Tray
    SD1456 功能描述:射頻雙極電源晶體管 NPN 28V 170-230MHz RoHS:否 制造商:M/A-COM Technology Solutions 配置:Single 直流集電極/Base Gain hfe Min:40 最大工作頻率:30 MHz 集電極—發射極最大電壓 VCEO:25 V 發射極 - 基極電壓 VEBO:4 V 集電極連續電流:20 A 最大直流電集電極電流: 功率耗散:250 W 封裝 / 箱體:Case 211-11 封裝:Tray
    SD1457 功能描述:射頻放大器 RF Bipolar Trans RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
    SD1458 功能描述:射頻放大器 RF Bipolar Trans RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
    SD1459 功能描述:射頻雙極電源晶體管 NPN 28V 170-230MHz RoHS:否 制造商:M/A-COM Technology Solutions 配置:Single 直流集電極/Base Gain hfe Min:40 最大工作頻率:30 MHz 集電極—發射極最大電壓 VCEO:25 V 發射極 - 基極電壓 VEBO:4 V 集電極連續電流:20 A 最大直流電集電極電流: 功率耗散:250 W 封裝 / 箱體:Case 211-11 封裝:Tray