- 您現在的位置：買賣IC網 > PDF目錄373370 > SCX15AN (Electronic Theatre Controls, Inc.) Precision Compensated Pressure Sensors PDF資料下載
參數資料
| 型號： | SCX15AN |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Precision Compensated Pressure Sensors |
| 中文描述： | 精密補償壓力傳感器 |
| 文件頁數： | 4/10頁 |
| 文件大小： | 219K |
| 代理商： | SCX15AN |
March 1998/053
SCX - Series
Precision Compensated Pressure Sensors
Aubinger Weg 27, 82178 Puchheim, Germany
Phone 0049 - (0) 89 80 08 30, Fax 0049 - (0) 89 8 00 83 33
http://www.sensortechnics.com
Physical Construction (Cutaway Diagram)
(Not drawn to scale)
APPLICATION INFORMATION
The following circuits show some typical designs using the SCX
series sensors. For specific applications information or assistance,
please contact your nearest Sensym sales office or the Sensym
factory.
Low Pressure Applications
For sensing pressures below 1 psi, the circuit shown in Figure A
uses the SCX01DN to provide a 2 to 5 V output for a 0 to 10 inch of
water column input pressure. This output signal is compatible with
many A/D converters and hence can be used to interface to a
microprocessor system. This low-cost circuit is easily adaptable
to lower full-scale pressures down to 5 inches of water column.
Circuit Description
The LM10 is used to provide a voltage reference for the excitation
voltage (V
E
), and for the voltage node V
. With this configuration,
V
and V
are not affected by noise or voltage variations in the
12 V power supply. R
is used to adjust V
REF
to set the initial offset
voltage at the output, V
OUT
.
The pressure signal, V
, and B
. (See
Sensym Application Note SSAN-17A for details on this amplifier)
R
is used to adjust the signal gain of the circuit. The output equation
is given below.
V
OUT
= V
IN
[ 2 (1+
R
/
R1
)]+V
REF
For the best circuit performance, a careful selection of components
in necessary. Use wirebound pots of insure low temperature
coefficients and low longterm drift. A five-element resistor array
(10k
) SIP should be used for the resistors in the amplifier stage in
order to obtain closely matched values and temperature
coefficients. All other resistors should be 1% metal film. Amplifiers
B
, and B
should have low offset voltage and low noise. Signal
lines should be as short as possible and the power supply should
be capacitively bypassed on the PC board.
Adjustment Procedure
1. With zero-pressure applied, adjust the offset adjust R
3
,
until V
OUT
= 2.000 V
2. Apply full-scale pressure (10 in. W.C) to port B
1
and adjust the
full-scale adjust R
2
, so that V
OUT
= 5.000 V.
3. Repeat procedure if necessary.
Medical Applications
For blood pressure monitoring applications, the circuit shown in
Figure B provides a 0.5 V to 3.5 V output for a 0 to 300 mm Hg input
pressure. The circuit is easily calibrated and is not affected by
changes in the voltage supply. Because 300 mm Hg is approximately
5.8 psi, an SCX05DN is used.
Circuit Description
The circuit shown here in Figure B is very similar to that shown in
Figure A. The internal 200 mV reference voltage of the LM10 is
amplified to provide power to the sensor and to provide a voltage
reference, V
. This allows the circuit to operate at a supply
voltage between 5 and 20 volts without affecting performance of
the circuit. By adjusting R
, V
is used to set the initial zero-
pressure voltage at V
. The pressure signal, V
, is amplified by
amplifiers B
and B
. These amplifiers should be precision op amps
with low offset voltages and high common-mode rejection. The
signal gain is adjusted by R
2
, and the overall equation for the output
voltage is given by ,
V
OUT
= V
IN
[ 2 (1+
R
/
R1
)]+V
REF
Adjustment Procedure
1. With zero-pressure applied, adjust the offset adjust
R
, until V
= 0.500 V
2. Apply full-scale pressure (300 mm Hg) to port B
1
and adjust
R
, until V
= 3.500 V.
3. Repeat procedure if necessary.
相關PDF資料 |
PDF描述 |
|---|---|
| SCX15DN | Precision Compensated Pressure Sensors |
| SCX30AN | Precision Compensated Pressure Sensors |
| SCX30DN | Precision Compensated Pressure Sensors |
| SD-A292B | CRYSTAL CLOCK OSCILLATORS |
| SD-A2920 | CRYSTAL CLOCK OSCILLATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCX15AN-90 | 功能描述:板上安裝壓力/力傳感器 JZ SILICON PRESSURE RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| SCX15ANC | 功能描述:板上安裝壓力/力傳感器 0 to15psid 6PIN SIP UNAMP ABSOLUTE 20V RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| SCX15ANC-90 | 制造商:Honeywell Sensing and Control 功能描述:SENSYM |
| SCX15DN | 功能描述:板上安裝壓力/力傳感器 0-15 PSID PRECISION TEMP RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| SCX15DN-90 | 制造商:Honeywell Sensing and Control 功能描述:Pressure Sensor 0psi to 15psi Differential/Gage 6-Pin |
發布緊急采購，3分鐘左右您將得到回復。