參數資料
型號： SCC2691AE1N24,602
廠商： NXP Semiconductors
文件頁數： 11/25頁
文件大?。?/td> 0K
描述： IC UART SINGLE 24-DIP
產品培訓模塊： Stand-Alone UARTs
標準包裝： 15
特點： 故障啟動位檢測
通道數： 1，UART
FIFO's： 3 位
電源電壓： 5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶CMOS： 是
安裝類型： 通孔
封裝/外殼： 24-DIP（0.300"，7.62mm）
供應商設備封裝： 24-DIP
包裝： 管件
其它名稱： 568-1215-5
935026990602
SCC2691AE1N24
Philips Semiconductors
Product data sheet
SCC2691
Universal asynchronous receiver/transmitter (UART)
2006 Aug 04
19
MASTER STATION
TxD
TRANSMITTER
ENABLED
TxRDY
(SR2)
CSN
(WRITE]
PERIPHERAL STATION
RxD
RECEIVER
ENABLED
RxRDY
(SR0)
RDN/WRN
ADD#1
1
D0
0
ADD#2
1
BIT 9
MR1[4:3] = 11
MR1[2] = 1
ADD#1 MR1[2] = 0 D0
MR1[2] = 1 ADD#2
0
ADD#1
1
D0
0
ADD#2
1
0
MR1[4:3] = 11
ADD#1
D0
SD
S = STATUS
D = DATA
SD
ADD#2
SD00130
Figure 12. Wake-Up Mode
The CTS, RTS, CTS Enable Tx signals
CTS (Clear To Send) is usually meant to be a signal to the
transmitter meaning that it may transmit data to the receiver. The
CTS input is on pin MPI. The CTS signal is active low; thus, it is
called CTSN.
RTS is usually meant to be a signal from the receiver indicating that
the receiver is ready to receive data. It is also active low and is,
thus, called RTSN. RTSN is on pin MP0. A receiver’s RTS output
will usually be connected to the CTS input of the associated
transmitter. Therefore, one could say that RTS and CTS are
different ends of the same wire!
MR2(4) is the bit that allows the transmitter to be controlled by the
CTS pin (MPI). When this bit is set to one AND the CTS input is
driven high, the transmitter will stop sending data at the end of the
present character being serialized. It is usually the RTS output of
the receiver that will be connected to the transmitter’s CTS input.
The receiver will set RTS high when the receiver FIFO is full AND
the start bit of the fourth character is sensed. Transmission then
stops with four valid characters in the receiver. When MR2(4) is set
to one, CTSN must be at zero for the transmitter to operate. If
MR2(4) is set to zero, the MP pin will have no effect on the operation
of the transmitter.
MR1(7) is the bit that allows the receiver to control MP0. When MP0
is controlled by the receiver, the meaning of that pin will be RTS.
However, a point of confusion arises in that MP0 may also be
controlled by the transmitter. When the transmitter is controlling this
pin, its meaning is not RTS at all. It is, rather, that the transmitter
has finished sending its last data byte. Programming the MP0 pin to
be controlled by the receiver and the transmitter at the same time is
allowed, but would usually be incompatible.
RTS can also be controlled by the commands 1010 and 1011 in the
command register. RTS is expressed at the MP0 pin which is still an
output port. Therefore, the state of MP0 should be set low (by
commands to the CR register) for the receiver to generate the
proper RTS signal. The logic at the output is basically a NAND of
the MP0 bit register and the RTS signal as generated by the
receiver. When the RTS flow control is selected via the MR(7) bit
the state of the MP0 register is not changed. Terminating the use of
“Flow Control” (via the MR registers) will return the MP0 pin to the
control of the MP0 register.
Transmitter Disable Note
The sequence of instructions enable transmitter — load transmit
holding register — disable transmitter will result in nothing being
sent if the time between the end of loading the transmit holding
register and the disable command is less that 3/16 bit time in the
16x mode or one bit time in the 1x mode. Also, if the transmitter,
while in the enabled state and underrun condition, is immediately
disabled after a single character is loaded to the transmit holding
register, that character will not be sent.
In general, when it is desired to disable the transmitter before the
last character is sent AND the TxEMT bit is set in the status register
(TxEMT is always set if the transmitter has underrun or has just
been enabled), be sure the TxRDY bit is active immediately before
issuing the transmitter disable instruction. TxRDY sets at the end of
the “start bit” time. It is during the start bit that the data in the
transmit holding register is transferred to the transmit shift register.
Non-standard baud rates are available as shown in Table 6 below,
via the BRG Test function.
相關PDF資料
PDF描述
SC16C2550BIB48,151 IC UART DUAL W/FIFO 48-LQFP
SC16C2550BIB48,128 IC UART DUAL W/FIFO 48-LQFP
SC16C650BIB48,157 IC UART SOT313-2
AT32UC3L016-AUR IC MCU AVR32 16K FLASH 48TQFP
SC16C650BIB48,128 IC UART SOT313-2
相關代理商/技術參數
參數描述
SCC2691AE1N24-S 功能描述:UART 接口集成電路 5V INDSTRL UART 1 C RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SCC2692 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual asynchronous receiver/transmitter DUART
SCC2692AC1A44 功能描述:UART 接口集成電路 2CH. 5V IND. UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SCC2692AC1A44,512 功能描述:UART 接口集成電路 2CH. 5V IND. UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SCC2692AC1A44,518 功能描述:UART 接口集成電路 5V INDUSTRIAL UART 2 CHANNEL RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*