- 您現在的位置：買賣IC網 > PDF目錄376339 > SCAN182245FSSMQB (National Semiconductor Corporation) Non-Inverting Transceiver with 25OHM Series Resistor Outputs PDF資料下載
參數資料
| 型號： | SCAN182245FSSMQB |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| 中文描述： | 非反相與25OHM系列電阻器輸出 |
| 文件頁數： | 11/18頁 |
| 文件大?。?/td> | 231K |
| 代理商： | SCAN182245FSSMQB |
SCAN ABT Live Insertion and Power Cycling Characteristics
SCAN ABT is intended to serve in Live Insertion backplane
applications. It provides 2nd Level Isolation
1
which indicates
that while external circuitry to control the output enable pin
is unnecessary, there may be a need to implement differen-
tial length backplane connector pins for V
CC
and GND. As
well, pre-bias circuitry for backplane pins may be necessary
to avoid capacitive loading effects during live insertion.
SCAN ABT provides control of output enable pins during
power cycling via the circuit in Figure A. It essentially con-
trols the G
n
pin until V
CC
reaches a known level.
Duringpower-up, when V
CC
ramps through the 0.0V to 0.7V
range, all internal device circuitry is inactive, leaving output
and I/O pins of the device in high impedance. From approxi-
mately 0.8V to 1.8V V
CC
, the Power-On-Reset circuitry,
(POR), in Figure A becomes active and maintains device
high impedance mode. The POR does this by providing a
low from its output that resets the flip-flop The output, Q, of
the flip-flop then goes high and disables the NOR gate from
an incidental low input on the G
n
pin. After 1.8V V
CC
, the
POR circuitry becomes inactive and ceases to control the
flip-flop. To bring the device out of high impedance, the G
n
input must receive an inactive-to-active transition, a high-to-
low transition on G
n
in this case to change the state of the
flip-flop. With a low on the Q output of the flip-flop, the NOR
gate is free to allow propagation of a G
n
signal.
During power-down, the Power-On-Reset circuitry will be-
come active and reset the flip-flop at approximately 1.8V
V
CC
. Again, the Q output of the flip-flop returns to a high and
disables the NOR gate from inputs from the G
n
pin. The
device will then remain in high impedance for the remaining
ramp down from 1.8V to 0.0V V
CC
.
Some suggestions to help the designer with live insertion
issues:
#
The G
n
pin can float during power-up until the Power-On-
Reset circuitry becomes inactive.
#
The G
n
pin can float on power-down only after the Pow-
er-On-Reset has become active.
The description of the functionality of the Power-On-Reset
circuitry can best be described in the diagram of Figure B.
TL/F/11657–19
FIGURE A
TL/F/11657–20
FIGURE B
1
Section 7, ‘‘Design Consideration for Fault Tolerant Backplanes’’, Application Note AN-881.
SCAN ABT includes additional power-on reset circuitry not otherwise included in ABT devices.
http://www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| SCAN182245FSSMX | Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| SCAN182245AFCX | Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| SCAN182245AFMQB | Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| SCAN182245AFMX | Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| SCAN182245ASSC | Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCAN182245FSSMX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| SCAN182245TFCQB | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| SCAN182245TFCX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| SCAN182245TFMQB | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
| SCAN182245TFMX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Non-Inverting Transceiver with 25OHM Series Resistor Outputs |
發布緊急采購，3分鐘左右您將得到回復。