參數資料
型號： SC28L198
廠商： NXP Semiconductors N.V.
英文描述： Octal UART for 3.3V and 5V supply voltage
中文描述： 八路的UART電源電壓為3.3V和5V
文件頁數： 19/56頁
文件大?。?/td> 345K
代理商： SC28L198
Philips Semiconductors
Product specification
SC28L198
Octal UART for 3.3V and 5V supply voltage
1999 Jan 14
19
Bit 7
áááááááááááááááááááááááááááááááá
á
áááááááááááááááááááááááááááááááá
á
á
á
á
á
áááááááááááááááááááááááááááááá
* If these bits are not 0 the characters will be stripped regardless of
bits (3:2) or (1:0)
á
á
á
á
Bit 6
Address Recognition *
transparency
0 – Address characters
received are pushed to
RxFIFO
1 – Address characters
received are
not
pushed
onto the RxFIFO
á
á
á
á
Bit 5:4
á
á
á
á
character when the RxFIFO has loaded to a depth of 12 characters.
Draining the RxFIFO to a level of 8 or less causes the Transmitter to
emit an Xon character. All transmissions require no host
involvement. A setting other than b’00 in this field precludes the use
of the command register to transmit Xon/Xoff characters.
Bit 3:2
á
á
á
á
Bit 1:0
Address Recognition
control
01 – Auto wake
10 – Auto doze
11 – Auto wake and
auto doze
áááááááááááááááááááááááááááááááá
áááááá
á
ááááá
ááááá
Xon/Xoff * transparency
á
11 – not full
interrupt
level
control
00 – empty
01 – 3/4 empty
10 – 1/2 empty
á
áááááááá
áááááááá
áááááááá
áááááááá
áááááááá
TxiNT
áááááááá
á
ááááá
ááááá
á
á
received are pushed onto
the
RxFIFO
1 – flow control characters
received are
not
pushed
onto the RxFIFO
á
á
á
á
á
á
á
á
MR0[7:6] –
Control the handling of recognized Xon/Xoff or Address
characters. If set, the character codes are placed on the RxFIFO
along with their status bits just as ordinary characters are. If the
character is not pushed onto the RxFIFO, its received status will be
lost unless the receiver is operating in the block error mode, see
MR1[5] and the general discussion on receiver error handling.
Interrupt processing is not effected by the setting of these bits. See
Character recognition section.
MR0[5:4] –
Controls the fill level at which a transmitter begins to
present its interrupt number to the interrupt arbitration logic. Use of
a low fill level minimizes the number of interrupts generated and
maximizes the number of transmit characters per interrupt cycle. It
also increases the probability that the transmitter will go idle for lack
of characters in the TxFIFO.
MR0[3:2] –
Controls the Xon/Xoff processing logic. Auto
Transmitter flow control allows the gating of Transmitter activity by
Xon/Xoff characters received by the Channel’s receiver. Auto
Receiver flow control causes the Transmitter to emit an Xoff
Note: Interrupt generation in Xon/Xoff processing is controlled by the
IMR (Interrupt Mask Register) of the individual channels. The
interrupt may be cleared by a read of the XISR, the Xon/Xoff
Interrupt Status Register. Receipt of a flow control character will
always generate an interrupt if the IMR is so programmed. The
MR0[3:2] bits have effect on the automatic aspects of flow control
only, not the interrupt generation.
MR0[1:0] –
This field controls the operation of the Address
recognition logic. If the device is not operating in the special or
“wake–up” mode, this hardware may be used as a general purpose
character detector by choosing any combination except b’00.
Interrupt generation is controlled by the channel IMR. The interrupt
may be cleared by a read of the XISR, the Xon/Xoff Interrupt Status
Register. See further description in the section on the Wake Up
mode.
Bit 7
Bit 6
RxRTS
Control
0 – off
1 – on
1 – ISR masked
áááááááááááááááááááááááááááááááá
áááááááááááááááááááááááááááááááá
á
áááááááááááááááááááááááááááááá
á
á
áááááááááááááááááááááááááááááá
MR1[7]: Receiver Request to Send Control
This bit controls the deactivation of the RTSN output (I/O2) by the
receiver. This output is asserted and negated by commands applied
via the command register. MR1[7] = 1 causes RTSN to be
automatically negated upon receipt of a valid start bit if the receiver
FIFO is full or greater. RTSN is reasserted when an the FIFO fill
level falls below full. This constitutes a change from previous
members of Philips (Signets)’ UART families where the RTSN
function triggered on FIFO full. This behavior caused problems with
PC UARTs that could not stop transmission at the proper time. .
The RTSN feature can be used to prevent overrun in the receiver, by
using the RTSN output signal, to control the CTSN input of the
transmitting device.
á
á
Bit 5
This bit controls the readout mode of the Interrupt Status Register,
ISR. If set, the ISR reads the current status masked by the IMR, i.e.
only interrupt sources enabled in the IMR can ever show a ’1’ in the
ISR. If cleared, the ISR shows the current status of the interrupt
source without regard to the Interrupt Mask setting.
Bit 4:3
Parity Mode
á
Bit 2
Parity Type
á
Bit 1:0
Bits per Charac-
ter
00 – 5
01 – 6
10 – 7
11 – 8
áá
á
áááááá
áááááá
á
ááááá
ááááá
ISR Read Mode
ááááá
á
11 – Special Mode
á
áááá
á
á
á
á
0 – ISR unmasked
á
á
0 = Character
1 = Block
á
00 – With Parity
01 – Force parity
10 – No parity
á
0 = Even
1 = Odd
á
á
MR1[6]: Interrupt Status Masking
MR1[5]: Error Mode Select
This bit selects the operating mode of the three FIFOed status bits
(FE, PE, received break). In the character mode, status is provided
on a character by character basis; the status applies only to the
character at. the bottom of the FIFO. In the block mode, the status
provided in the SR for these bits is the accumulation (logical OR) of
the status for all characters coming to the top of the FIFO, since the
last reset error command was issued.
MR1[4:3]: Parity Mode Select
相關PDF資料
PDF描述
SC28L198A1 Octal UART for 3.3V and 5V supply voltage
SC28L198C1A Cable Ties; Color:Black; Pack Quantity:100
SC28C198A1A Octal UART for 3.3V and 5V supply voltage
SC28L202A1 Dual universal asynchronous receiver/transmitter DUART
SC28L202 Dual universal asynchronous receiver/transmitter DUART
相關代理商/技術參數
參數描述
SC28L198A1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Octal UART for 3.3V and 5V supply voltage
SC28L198A1A 功能描述:UART 接口集成電路 UART OCTAL W/FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L198A1A,512 功能描述:UART 接口集成電路 UART OCTAL W/FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L198A1A,518 功能描述:UART 接口集成電路 3V-5V 8CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L198A1A,529 功能描述:UART 接口集成電路 3V-5V 8CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*