- 您現在的位置：買賣IC網 > PDF目錄3764 > SC28C94A1A,518 (NXP Semiconductors)IC UART QUAD W/FIFO 52-PLCC PDF資料下載
參數資料
| 型號： | SC28C94A1A,518 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 15/39頁 |
| 文件大小： | 0K |
| 描述： | IC UART QUAD W/FIFO 52-PLCC |
| 產品培訓模塊： | Stand-Alone UARTs |
| 標準包裝： | 1 |
| 特點： | 故障啟動位檢測 |
| 通道數： | 4，QUART |
| FIFO's： | 8 字節 |
| 電源電壓： | 5V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 52-LCC（J 形引線） |
| 供應商設備封裝： | 52-PLCC（19.2x19.2） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 828 (CN2011-ZH PDF) |
| 其它名稱： | 568-1114-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Philips Semiconductors
Product data sheet
SC28C94
Quad universal asynchronous receiver/transmitter (QUART)
2006 Aug 09
22
I/O Port Control Channel B (IOPCRB)
IOPCR[xx]
IOPCRb[7:6]
IOPCRb[5:4]
IOPCRb[3:2]
IOPCRb[1:0]
Pin Control Bits
I/O3B
I/O2B
I/O1B
I/O0B
00 = input
IPR(7), TxC in
IPR(6), RxC in
IPR(3), TxC in
IPR(2), CTSN
01 = output
OPRab(7)
OPRab(6)
RTSN1 if IOPCR[5:4] = 01
OPRab(3)
RTSN2 if IOPCR[5:4]
≠ 01
OPRab(2)
10 = output
TxC 16x
RxC 1x
C/T ab out
TxC 1x
11 = output
TxC 1x
RxC 16x
RxC 1x
TxC 16x
I/O Port Control Channel C (IOPCRC)
IOPCR[xx]
IOPCRc[7:6]
IOPCRc[5:4]
IOPCRc[3:2]
IOPCRc[1:0]
Pin Control Bits
I/O3C
I/O2C
I/O1C
I/O0C
00 = input
IPR(5), TxC in
IPR(4), RxC in
IPR(1), C/Tcd Clk in1 TxC in
IPR(0), CTSN
01 = output
OPRcd(5)
OPRcd(4)
RTSN1 if IOPCR[5:4] = 01
OPRab(1)
RTSN2 if IOPCR[5:4]
≠ 01
OPRcd(0)
10 = output
TxC 16x
RxC 1x
RxC 16x
TxC 1x
11 = output
TxC 1x
RxC 16x
RxC 1x
TxC 16x
I/O Port Control Channel D (IOPCRD)
IOPCR[xx]
IOPCRd[7:6]
IOPCRd[5:4]
IOPCRd[3:2]
IOPCRd[1:0]
Pin Control Bits
I/O3D
I/O2D
I/O1D
I/O0D
00 = input
IPR(7), TxC in
IPR(6), RxC in
IPR(3), TxC in
IPR(2), CTSN
01 = output
OPRcd(7)
OPRcd(6)
RTSN1 if IOPCR[5:4] = 01
OPRcd(3)
RTSN2 if IOPCR[5:4]
≠ 01
OPRcd(2)
10 = output
TxC 16x
RxC 1x
C/T cd out
TxC 1x
11 = output
TxC 1x
RxC 16x
RxC 1x
TxC 16x
The input part of the I/O pins is always active. The programming of the IOPCR bits to 00 merely turns off the out drivers and places
the pin at high impedance.
A read of the IPR register returns the value of the IPR bits as shown above. IPR(5) is at bit position 5 of the data bus. Note that the IPR bit
positions do not follow the 0, 1, 2, 3 order of the I/O ports. During a read of the IPR the I/O ports are not latched. Therefore, it is possible to see
changing data during the read. Port pins that have clocks on them may not yield valid data during the read.
Since the input circuits of the I/O ports are always active it is possible to direct the port signal back into the port. For example: I/O1 will output
the RTS signal. Setting the Counter/Timer (C/T) to be clocked by the I/O1 port will result in the counter counting the number of times RTS goes
active. The change of state detectors on I/O0 and I/O1 will, when programmed, always be sensitive to the signal on the port regardless of the
source of that port’s signal.
NOTES:
1. Normal configurations place RTSN output on I/O1 and place Tx external clock input on I/O3. For the 48 pin Dual In-Line package, I/O3 is
not available. The following options allow flexible I/O programming with the 48 pin package:
When IOPCR(7:6), the I/O3 control,
≠ 00, then I/O1 becomes available to the transmitter as an external clock.
When IOPCR(5:4), the I/O2 control, = 01, then I/O2 may be the RTSN signal if MR1(7) = 1 and OPR(4) = 1.
2. I/O1 becomes RTSN when IOPCR(3:2) = 01 and MR1(7) = 1 and OPR(1) = 1. (OPR(3) for channel B)
3. Recommended method for setting RTS/CTS flow control is to set IPCR [5:4] to 01 and to set I/OPCR[1:0] to 00. This makes I/O[2} RTSN
and I/O[1] CTSN. Caution: When RTS/CTS is active writing to the OPR register could conflict with the receiver control of OPR [6] and
OPR [4].
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C754BIA68,518 | IC UART QUAD W/FIFO 68-PLCC |
| SC26C92C1N,602 | IC UART DUAL W/FIFO 40-DIP |
| SC28L91A1B,551 | IC UART SINGLE W/FIFO 44-PQFP |
| SC28L91A1B,528 | IC UART SINGLE W/FIFO 44PQFP |
| SC28L91A1A,529 | IC UART SINGLE W/FIFO 44-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC28C94A1AB | 制造商:PHILIPS-SEMI 功能描述: |
| SC28C94A1N | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad universal asynchronous receiver/transmitter QUART |
| SC28C94A1N,112 | 功能描述:IC UART QUAD W/FIFO 48-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - UART（通用異步接收器/發送器） 系列:- 標準包裝:250 系列:- 特點:* 通道數:2，DUART FIFO's:16 字節 規程:RS232，RS485 電源電壓:2.25 V ~ 5.5 V 帶并行端口:- 帶自動流量控制功能:是 帶IrDA 編碼器/解碼器:是 帶故障啟動位檢測功能:是 帶調制解調器控制功能:是 帶CMOS:是 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:托盤 其它名稱:XR16L2551IM-F-ND |
| SC28L194 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART for 3.3V and 5V supply voltage |
| SC28L194A1A | 功能描述:UART 接口集成電路 3V-5V 4CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。