- 您現在的位置：買賣IC網 > PDF目錄374723 > SC2602STRT (Semtech Corporation) Synchronous Voltage Mode Controller for Distributed Power Supply Applications PDF資料下載
參數資料
| 型號： | SC2602STRT |
| 廠商： | Semtech Corporation |
| 英文描述： | Synchronous Voltage Mode Controller for Distributed Power Supply Applications |
| 中文描述： | 同步電壓模式控制器，用于分布式電源應用 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 316K |
| 代理商： | SC2602STRT |
6
2004 Semtech Corp.
www.semtech.com
POWER MANAGEMENT
Applications Information (Cont.)
SC2602/SC2602A
Soft Start
Initially, SS/SHDN sources 10μA of current to charge an
external capacitor. The outputs of the error amplifiers
are clamped to a voltage proportional to the voltage on
SS/SHDN. This limits the on-time of the high-side
MOSFETs, thus leading to a controlled ramp-up of the
output voltages.
R
Current Limiting
The current limit threshold is set by connecting an exter-
nal resistor from the V
supply to OCSET. The voltage
drop across this resistor is due to the 200μA internal
sink sets the voltage at the pin. This voltage is compared
to the voltage at the PHASE node. This comparison is
made only when the high-side drive is high to avoid false
current limit triggering due to uncontributing measure-
ments from the MOSFETs off-voltage. When the voltage
at PHASE is less than the voltage at OCSET, an overcurrent
condition occurs and the soft start cycle is initiated. The
synchronous switch turns off and SS/SHDN starts to
sink 2μA. When SS/SHDN reaches 0.8V, it then starts
to source 10μA and a new cycle begins.
Hiccup Mode
During power up, the SS/SHDN pin is internally pulled
low until VCC reaches the undervoltage lockout level of
4.2V. Once V
has reached 4.2V, the SS/SHDN pin is
released and begins to source 10μA of current to the
external soft-start capacitor. As the soft-start voltage
rises, the output of the internal error amplifier is clamped
to this voltage. When the error signal reaches the level
of the internal triangular oscillator, which swings from 1V
to 2V at a fixed frequency of 200kHz/500kHz, switching
occurs. As the error signal crosses over the oscillator
signal, the duty cycle of the PWM signal continues to in-
crease until the output comes into regulation. If an over-
current condition has not occurred the soft-start voltage
will continue to rise and level off at about 2.2V.
An over-current condition occurs when the high-side drive
is turned on, but the PHASE node does not reach the
voltage level set at the OCSET pin. The PHASE node is
sampled only once per cycle during the valley of the tri-
angular oscillator. Once an over-current occurs, the high-
side drive is turned off and the low-side drive turns on
and the SS/SHDN pin begins to sink 2μA. The soft-start
voltage will begin to decrease as the 2μA of current dis-
charges the external capacitor. When the soft-start volt-
age reaches 0.8V, the SS/SHDN pin will begin to source
10μA and begin to charge the external capacitor causing
the soft-start voltage to rise again. Again, when the soft-
start voltage reaches the level of the internal oscillator,
switching will occur.
If the over-current condition is no longer present, normal
operation will continue. If the over-current condition is
still present, the SS/SHDN pin will again begin to sink
2μA. This cycle will continue indefinitely until the over-
current condition is removed.
In conclusion, below is shown a typical “12V Application
Circuit” which has a BSTH voltage derived by bootstrapping
input voltage to the PHASE node through diode D1. This
circuit is very useful in cases where only input power of
12V is available.
In order to prevent substrate glitching, a small-signal di-
ode should be placed in close proximity to the chip with
cathode connected to PHASE and anode connected to
PGND.
相關PDF資料 |
PDF描述 |
|---|---|
| SC2603EVB | Simple PWM Boost Controller |
| SC2603SKTRT | Simple PWM Boost Controller |
| SC2603 | Simple PWM Boost Controller |
| SC2608A | Simple, Synchronous Voltage Mode PWM Controller |
| SC2608AEVB | Simple, Synchronous Voltage Mode PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC2603 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Simple PWM Boost Controller |
| SC2603ASK.TRT | 制造商:Semtech Corporation 功能描述: |
| SC2603ASKTRT | 制造商:Semtech Corporation 功能描述:SIMPLE INT COMPENSATED CONT |
| SC2603EVB | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Simple PWM Boost Controller |
| SC2603SKTRT | 制造商:Semtech Corporation 功能描述:Voltage Mode PWM Controller 800mA 6-Pin SOT-23 T/R 制造商:Semtech Corporation 功能描述:Simple PWM Boost Controller SOT23-6 |
發布緊急采購，3分鐘左右您將得到回復。