- 您現在的位置：買賣IC網 > PDF目錄374721 > SC2422AEVB (Semtech Corporation) BIPHASE CURRENT MODE CONTROLLER PDF資料下載
參數資料
| 型號： | SC2422AEVB |
| 廠商： | Semtech Corporation |
| 英文描述： | BIPHASE CURRENT MODE CONTROLLER |
| 中文描述： | 雙相電流模式控制器 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 114K |
| 代理商： | SC2422AEVB |
SC2422A
BIPHASE CURRENT MODE
CONTROLLER
2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320
PRELIMINARY - August 7, 2000
7
Applications Information
The SC2422A is an Input Current Mode Controller de-
signed for High Current, High performance two phase
DC/DC converters. The Current mode control is imple-
mented by generating the PWM ramp from the Input
Current, rather than the output current. This has the
advantage of eliminating the output current sense re-
sistors, and the power loss associated with output cur-
rent sensing. Eliminating the output current sense re-
sistors has the added advantage of improving the tran-
sient response by reducing the output impedance.
The output voltage is programmed via a 5-bit DAC in
32 steps. A novel technique allows programmable
DAC step size and output offset, allowing the SC2422A
based DC/DC converters to work in VRM9.0, VRM 8.3,
VRM8.4, VRM8.5 or future specified voltage ranges.
Theory of Operation
Pulse by Pulse Current Matching
The operation of the Input Current Mode, ICM, is as
follows:
The SC2422A Oscillator generates the OUT1 and
OUT2 logic output drives. OUT1 and OUT2 are non-
overlapping and sequentially command an external,
power MOSFET driver to turn on the Top MOSFETs.
When the Top MOSFET is enhanced (each phase),
the input voltage is impressed across the MOSFET
and the output Inductor. The AC current in the inductor
is:
Where F is the frequency (per phase) and L is the out-
put inductor. D is the duty cycle and is approximately
equal to V
/V
. The approximation arises from the
fact that the Duty cycle extends slightly to compensate
for losses in the current path. These losses include
RDS_ON of the MOSFET, the Equivalent Series Re-
sistance of the Inductors and the PCB trace resis-
tances.
The inductor current flows in the input current sense
resistor, generating a PWM ramp, same as in all cur-
rent mode controllers. The ramp is compared with an
amplified, level shifted and filtered version of the output
voltage at the PWM comparator. The comparator then
outputs a gate drive pulse that terminates when the
ramp voltage equals the error amplifier output signal.
The current mode control is inherently immune to input
voltage changes because the ramp amplitude reflects
the input voltage changes.
Since the input current sense resistor is the same for
both phases, the inherent inaccuracy due to mismatch
between output current sense resistors is avoided.
Also, since the comparator threshold is the same for
both phases, accurate current matching is achieved
between phases. This implements a pulse by pulse
current matching with a faster response to changes in
output current by monitoring the input current for each
phase.
Programming the SC2422A
Figure 2 below, is the connection schematic for the In-
ternal Error Amplifier.
Figure 2: Error amplifier connections
The external components, R
, R
and R
set the DAC
step size, output voltage offset and droop, accordingly.
A resistor from R
(pin 8) to ground programs the
frequency as well as the DAC
current
step size.
Programming the Switching Frequency
The oscillator frequency can be selected first by setting
the value of R
REF
resistor (pin 8) to ground.
The switching frequency per phase is 1/2 of the above
oscillator frequency.
FxL
D
x
)
V
V
(
L
T
x
)
V
V
(
IL
OUT
IN
ON
OUT
IN
=
=
V
12
V
R
kHz
500
*
k
13
f
IN
REF
OSC
=
=
BGOUT (P15)
ERROUT(P6)
VOUT
FB(P7)
Ccomp
+
-
Ri
3K
Ros
Rf
Rcomp
E/A
Vid0
Io
Vid4
Bandgap
DAC
相關PDF資料 |
PDF描述 |
|---|---|
| SC2434 | TriPhase Current Mode Controller with Power Good |
| SC2434EVB | TriPhase Current Mode Controller with Power Good |
| SC2434SWTR | TriPhase Current Mode Controller with Power Good |
| SC2434SWTRT | TriPhase Current Mode Controller with Power Good |
| SC2434TSTR | TriPhase Current Mode Controller with Power Good |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC2424CSWTR | 制造商:Semtech Corporation 功能描述:4 Phase Current Mode Controller |
| SC2424CSWTRT | 制造商:Semtech Corporation 功能描述:MULTIPHASE CURRNT MODE CONTRLR |
| SC24-2R2-R | 功能描述:INDUCTOR SHIELD 2.2UH 800MA SMD RoHS:是 類別:電感器，線圈，扼流圈 >> 固定式 系列:SC24 標準包裝:500 系列:1331 電感:1.2µH 電流:247mA 電流 - 飽和:247mA 電流 - 溫升:- 類型:鐵芯體 容差:±10% 屏蔽:屏蔽 DC 電阻(DCR):最大 730 毫歐 Q因子@頻率:40 @ 7.9MHz 頻率 - 自諧振:130MHz 材料 - 芯體:鐵 封裝/外殼:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安裝類型:表面貼裝 包裝:帶卷 (TR) 工作溫度:-55°C ~ 105°C 頻率 - 測試:7.9MHz |
| SC2430 | 制造商:SYSTEMSENSOR 制造商全稱:SYSTEMSENSOR 功能描述:Strobes and Horn Strobes |
| SC2430W | 制造商:GAMEWELL-FCI 制造商全稱:GAMEWELL-FCI 功能描述:SC Strobes and PC Horn/Strobes |
發布緊急采購，3分鐘左右您將得到回復。