- 您現在的位置：買賣IC網 > PDF目錄374721 > SC2422 (Semtech Corporation) BIPHASE CURRENT MODE CONTROLLER PDF資料下載
參數資料
| 型號： | SC2422 |
| 廠商： | Semtech Corporation |
| 英文描述： | BIPHASE CURRENT MODE CONTROLLER |
| 中文描述： | 雙相電流模式控制器 |
| 文件頁數： | 8/10頁 |
| 文件大小： | 114K |
| 代理商： | SC2422 |
SC2422A
BIPHASE CURRENT MODE
CONTROLLER
2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320
PRELIMINARY - August 7, 2000
8
Programming the DAC Step Size
The SC2422A allows programming the output voltage
and the DAC step size by selecting external resistors.
The DAC
current
step size, for one MSB is:
where R
REF
is the resistor from R
REF
pin to Ground.
The DAC MSB
voltage
step size is calculated as fol-
lows:
V
DAC_MSB
= I
DAC_MSB
* R
I
or
Note that changing R
affects both frequency and
DAC step size. R
must be proportionally adjusted to
keep the same step size at different frequencies. The
advantage of this method is that all new VID specifica-
tions can be accommodated by modifying external
components while maintaining the required precision
without the need for converter redesign.
Programming the DAC Offset Voltage
Kirchoff’s current law can be applied to the error ampli-
fier’s Inverting node (see figure 2) to calculate R
, the
DAC offset setting resistor. The output Offset at zero
DAC current (VID=00000), is set as follows:
Where V
is the error amplifier output voltage and as
a first approximation is equal to 1.75V.
Where V
= Precision Reference Voltage = 1.50V.
The value of R
can be fine trimmed using a poten-
tiometer connected from the FB pin to ground.
Programming the Dynamic (Active) Droop
The SC2422A employs a novel approach to active
drooping for optimum transient response. The output
voltage is regulated as a function of output current. At
zero current the output is regulated to the upper limit of
the output voltage specification. As the load is in-
creased, the output “droops” towards the lower limit.
This makes optimum use of the output voltage error
band, yielding minimum output capacitor size and cost.
Active drooping, does not compromise the converter
response time as does passive droop techniques. The
active droop also allows for an accurate Inter-Module
current sharing scheme, where multiple DC/DC con-
verters are required to share the current required by a
DC bus. As one module supplies more current, that
modules output voltage ”droops”, allowing other mod-
ules to provide the balance of the required current.Any
changes in the output voltage is instantaneously re-
flected to the error amplifier, which has a high Slew
Rate and wide Gain-Bandwidth product to recover the
output voltage to its nominal level with minimal delay.
The droop is adjusted by setting the feedback resistor,
Rf. While the optimum value of R
may be derived ex-
perimentally, the following equation can provide the
droop at a given output current:
The Gain of the current amplifier is set to 20 (26dB),
while R
S
is the input sense resistor.
The effective inductance of the sense resistor must be
minimized to achieve accurate correlation between the
above equation and actual droop achieved. This is be-
cause the inductive spike, which may also be caused
by layout inductance's, will alter the PWM comparator
trip point. The value of R
may have to be adjusted to
compensate for such parasitic effects.
Since Rf also sets the DC gain of the system, changing
the value of Rf affects the offset voltage, which is set
via Ros. The value of Ros can be modified to achieve
exact offset after the droop resistor has been chosen.It
must be noted that the Current Amplifier gain is quite
precise, with greater than 80dB of Common Mode Re-
jection Ratio (CMRR). Thus the droop’s accuracy is
limited primarily by external components tolerances
and the external parasitic effects.
Loop Gain Considerations
The Modulator gain in Input Current Mode control is
equal to:
RAMP
V
IN
MOD
V
K
=
L
V
V
X
G
X
T
X
R
V
3
V
O
IN
CA
OSC
SENSE
RAMP
+
=
32
R
R
V
V
I
REF
BG
LSB
_
DAC
=
REF
BG
MSB
_
DAC
I
R
V
=
F
BG
EO
I
BG
O
BG
OS
R
V
V
R
V
V
V
R
+
=
RF
OUT
S
I
2
CA
DROOP
V
I
*
R
*
R
*
G
=
32
V
V
MSB
_
DAC
LSB
_
DAC
=
相關PDF資料 |
PDF描述 |
|---|---|
| SC2422ACSTR | BIPHASE CURRENT MODE CONTROLLER |
| SC2422A | BIPHASE CURRENT MODE CONTROLLER |
| SC2422AEVB | BIPHASE CURRENT MODE CONTROLLER |
| SC2434 | TriPhase Current Mode Controller with Power Good |
| SC2434EVB | TriPhase Current Mode Controller with Power Good |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC24-220-R | 功能描述:INDUCTOR SHIELD 22UH 180MA SMD RoHS:是 類別:電感器，線圈，扼流圈 >> 固定式 系列:SC24 標準包裝:500 系列:1331 電感:1.2µH 電流:247mA 電流 - 飽和:247mA 電流 - 溫升:- 類型:鐵芯體 容差:±10% 屏蔽:屏蔽 DC 電阻(DCR):最大 730 毫歐 Q因子@頻率:40 @ 7.9MHz 頻率 - 自諧振:130MHz 材料 - 芯體:鐵 封裝/外殼:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安裝類型:表面貼裝 包裝:帶卷 (TR) 工作溫度:-55°C ~ 105°C 頻率 - 測試:7.9MHz |
| SC24-221-R | 功能描述:INDUCTOR SHIELD 220UH 80MA SMD RoHS:是 類別:電感器，線圈，扼流圈 >> 固定式 系列:SC24 標準包裝:500 系列:1331 電感:1.2µH 電流:247mA 電流 - 飽和:247mA 電流 - 溫升:- 類型:鐵芯體 容差:±10% 屏蔽:屏蔽 DC 電阻(DCR):最大 730 毫歐 Q因子@頻率:40 @ 7.9MHz 頻率 - 自諧振:130MHz 材料 - 芯體:鐵 封裝/外殼:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安裝類型:表面貼裝 包裝:帶卷 (TR) 工作溫度:-55°C ~ 105°C 頻率 - 測試:7.9MHz |
| SC24-222-R | 功能描述:INDUCTOR SHIELD 2200UH 20MA SMD RoHS:是 類別:電感器，線圈，扼流圈 >> 固定式 系列:SC24 標準包裝:500 系列:1331 電感:1.2µH 電流:247mA 電流 - 飽和:247mA 電流 - 溫升:- 類型:鐵芯體 容差:±10% 屏蔽:屏蔽 DC 電阻(DCR):最大 730 毫歐 Q因子@頻率:40 @ 7.9MHz 頻率 - 自諧振:130MHz 材料 - 芯體:鐵 封裝/外殼:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安裝類型:表面貼裝 包裝:帶卷 (TR) 工作溫度:-55°C ~ 105°C 頻率 - 測試:7.9MHz |
| SC2422A | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:BIPHASE CURRENT MODE CONTROLLER |
| SC2422ACSTR | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:BIPHASE CURRENT MODE CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。