參數資料
型號: SC16C850LIET
廠商: NXP Semiconductors N.V.
元件分類: 收發器
英文描述: 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode parallel bus interface
封裝: SC16C850LIB<SOT313|<<<1<Always Pb-free,;SC16C850LIB<SOT313|<<<1<Always Pb-free,;SC16C850LIB<SOT313|<<<1<Always Pb-free,;SC16C850LIBS<SOT617-1 (HVQFN3
文件頁數: 35/55頁
文件大?。?/td> 1029K
代理商: SC16C850LIET
SC16C850L
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 1 February 2011
35 of 55
NXP Semiconductors
SC16C850L
1.8 V single UART with 128-byte FIFOs and IrDA encoder/decoder
7.20 RS-485 Turn-around Time Delay (RS485TIME)
The value in this register controls the turn-around time of the external line transceiver in
bit time. In automatic 9-bit mode RTS or DTR pin is used to control the direction of the line
driver, after the last bit of data has been shifted out of the transmit shift register the UART
will count down the value in this register. When the count value reaches zero, the UART
will assert RTS or DTR pin (logic 0) to turn the external RS-485 transceiver around for
receiving.
Table 30.
Bit
7:0
7.21 Advanced Feature Control Register 2 (AFCR2)
Table 31.
Bit
7:6
5
RS-485 programmable turn-around time register bits description
Symbol
Description
RS485TIME[7:0]
External RS-485 transceiver turn-around time delay. The value
represents the bit time at the programmed baud rate.
Advanced Feature Control Register 2 register bits description
Symbol
Description
AFCR2[7:6]
reserved
AFCR2[5]
RTSInvert. Invert RTS or DTR signal in automatic 9-bit mode.
logic 0 = RTS or DTR is set to 0 by the UART during transmission,
and to 1 during reception
logic 1 = RTS or DTR is set to 1 by the UART during transmission,
and to 0 during reception
AFCR2[4]
RTSCon. Enable the transmitter to control RTS or DTR pin in
automatic 9-bit mode.
logic 0 = transmitter does not control RTS or DTR pin
logic 1 = transmitter controls RTS or DTR pin
AFCR2[3]
RS485 RTS/DTR. Select RTS or DTR pin to control the external
transceiver.
logic 0 = RTS pin is used to control the external transceiver
logic 1 = DTR pin is used to control the external transceiver
AFCR2[2]
TXDisable. Disable transmitter
logic 0 = transmitter is enabled
logic 1 = transmitter is disabled
AFCR2[1]
RXDisable. Disable receiver
logic 0 = receiver is enabled
logic 1 = receiver is disabled
AFCR2[0]
9-bitMode. Enable 9-bit mode or Multidrop (RS-485) mode
logic 0 = normal RS-232 mode
logic 1 = enable 9-bit mode
4
3
2
1
0
相關PDF資料
PDF描述
SC16C850SVIBS 1.8 V single UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
SC16C850VIBS 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
SC16C852LIB 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface
SC16C852LIBS 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface
SC16C852LIET 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface
相關代理商/技術參數
參數描述
SC16C850LIET,115 功能描述:UART 接口集成電路 1.8V 1 CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850LIET,118 功能描述:UART 接口集成電路 UART 1-CH 128Byte FIFO 1.8V 36-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850LIET,151 功能描述:UART 接口集成電路 1.8V 1 CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850LIET,157 功能描述:UART 接口集成電路 1.8V 1 CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850LIET,515 制造商:NXP Semiconductors 功能描述: