參數資料
型號: SC16C754BIBM,157
廠商: NXP Semiconductors
文件頁數: 19/50頁
文件大小: 0K
描述: IC UART QUAD 64BYTE 64LQFP
標準包裝: 1,250
通道數: 4,QUART
FIFO's: 64 字節
電源電壓: 2.5V,3.3V,5V
帶自動流量控制功能:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
安裝類型: 表面貼裝
封裝/外殼: 64-LQFP
供應商設備封裝: 64-LQFP(7x7)
包裝: 托盤
其它名稱: 935279069157
SC16C754BIBM
SC16C754BIBM-ND
SC16C754B_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 6 October 2008
26 of 51
NXP Semiconductors
SC16C754B
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
7.5 Line Status Register (LSR)
Table 13 shows the line status register bit settings.
When the LSR is read, LSR[4:2] reect the error bits (BI, FE, PE) of the character at the
top of the RX FIFO (next character to be read). The LSR[4:2] registers do not physically
exist, as the data read from the RX FIFO is output directly onto the output data bus,
DI[4:2], when the LSR is read. Therefore, errors in a character are identied by reading
the LSR and then reading the RHR.
LSR[7] is set when there is an error anywhere in the RX FIFO, and is cleared only when
there are no more errors remaining in the FIFO.
Reading the LSR does not cause an increment of the RX FIFO read pointer. The RX FIFO
read pointer is incremented by reading the RHR.
Table 13.
Line status register bits description
Bit
Symbol
Description
7
LSR[7]
FIFO data error.
logic 0 = no error (normal default condition)
logic 1 = at least one parity error, framing error, or break indication is in the
receiver FIFO. This bit is cleared when no more errors are present in the
FIFO.
6
LSR[6]
THR and TSR empty. This bit is the Transmit Empty indicator.
logic 0 = transmitter hold and shift registers are not empty
logic 1 = transmitter hold and shift registers are empty
5
LSR[5]
THR empty. This bit is the Transmit Holding Register Empty indicator.
logic 0 = Transmit Hold Register is not empty
logic 1 = Transmit Hold Register is empty. The processor can now load up
to 64 bytes of data into the THR if the TX FIFO is enabled.
4
LSR[4]
Break interrupt.
logic 0 = no break condition (normal default condition)
logic 1 = a break condition occurred and associated byte is 00, that is,
RX was LOW for one character time frame
3
LSR[3]
Framing error.
logic 0 = no framing error in data being read from RX FIFO (normal default
condition)
logic 1 = framing error occurred in data being read from RX FIFO, that is,
received data did not have a valid stop bit
2
LSR[2]
Parity error.
logic 0 = no parity error (normal default condition)
logic 1 = parity error in data being read from RX FIFO
1
LSR[1]
Overrun error.
logic 0 = no overrun error (normal default condition)
logic 1 = overrun error has occurred
0
LSR[0]
Data in receiver.
logic 0 = no data in receive FIFO (normal default condition)
logic 1 = at least one character in the RX FIFO
相關PDF資料
PDF描述
VI-B5J-IW-F3 CONVERTER MOD DC/DC 36V 100W
VI-BN0-IY CONVERTER MOD DC/DC 5V 50W
VI-B5J-IW-F2 CONVERTER MOD DC/DC 36V 100W
VI-B54-IX-F4 CONVERTER MOD DC/DC 48V 75W
0757830350 CONN RCPT IPASS R/A 68POS SMD
相關代理商/技術參數
參數描述
SC16C754BIBM-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIBM-S 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754IA68 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO
SC16C754IA68,512 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754IA68,518 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel