參數資料
型號： SC16C754B
廠商： NXP Semiconductors N.V.
英文描述： 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
中文描述： 5伏，3.3伏和2.5伏兆5四異步/秒（最大）64字節的FIFO
文件頁數： 33/50頁
文件大小： 259K
代理商： SC16C754B
9397 750 14668
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 02 — 13 June 2005
33 of 50
Philips Semiconductors
SC16C754B
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
The FIFO Rdy register is a read-only register that can be accessed when any of the two
UARTs is selected CSA - CSD = 0, MCR[2] (FIFO Rdy Enable) is a logic 1, and loop-back
is disabled. The address is 111.
8.
Programmer’s guide
The base set of registers that is used during high-speed data transfer have a
straightforward access method. The extended function registers require special access
bits to be decoded along with the address lines. The following guide will help with
programming these registers. Note that the descriptions below are for individual register
access. Some streamlining through interleaving can be obtained when programming all
the registers.
Table 23:
Command
set baud rate to VALUE1, VALUE2
Register programming guide
Actions
read LCR (03), save in temp
set LCR (03) to 80
set DLL (00) to VALUE1
set DLM (01) to VALUE2
set LCR (03) to temp
read LCR (03), save in temp
set LCR (03) to BF
set Xoff1 (06) to VALUE1
set Xon1 (04) to VALUE2
set LCR (03) to temp
read LCR (03), save in temp
set LCR (03) to BF
set Xoff-2 (07) to VALUE1
set Xon-2 (05) to VALUE2
set LCR (03) to temp
read LCR (03), save in temp
set LCR (03) to BF
set EFR (02) to VALUE
set LCR (03) to temp
read LCR (03), save in temp1
set LCR (03) to BF
read EFR (02), save in temp2
set EFR (02) to 10 + temp2
set LCR (03) to 00
read MCR (04), save in temp3
set MCR (04) to 40 + temp3
set TCR (06) to VALUE
set MCR (04) to temp3
set LCR (03) to BF
set EFR (02) to temp2
set LCR (03) to temp1
set Xoff1, Xon1 to VALUE1, VALUE2
set Xoff2, Xon2 to VALUE1, VALUE2
set software flow control mode to VALUE
set flow control threshold to VALUE
相關PDF資料
PDF描述
SC68C752B 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs and Motorola mP interface
SCAN182245AMTD Non-Inverting Transceiver with 25ohm Series Resistor Outputs
SCAN18245TSSC Non-Inverting Transceiver with 3-STATE Outputs
SCAN18374T D-Type Flip-Flop with 3-STATE Outputs
SCAN18374TSSC D-Type Flip-Flop with 3-STATE Outputs
相關代理商/技術參數
參數描述
SC16C754BIA68 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,512 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,518 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68,529 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C754BIA68512 制造商:NXP Semiconductors 功能描述:IC QUAD UART FIFO 5MBPS 5.5V LCC-68
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*