- 您現在的位置：買賣IC網 > PDF目錄11815 > SC16C554IB64,157 (NXP Semiconductors)IC UART QUAD W/FIFO 64-LQFP PDF資料下載
參數資料
| 型號： | SC16C554IB64,157 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 55/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART QUAD W/FIFO 64-LQFP |
| 標準包裝： | 800 |
| 通道數： | 4，QUART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.5V，3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 568-1321 935270074157 SC16C554IB64 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁
Philips Semiconductors
SC16C554/554D
Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 05 — 10 May 2004
9 of 55
9397 750 13132
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
5.2 Pin description
Table 2:
Pin description
Symbol
Pin
Type
Description
PLCC68 LQFP64 LQFP80
16/68
31
-
I
16/68 Interface type select (input with internal pull-up). This input
provides the 16 (Intel) or 68 (Motorola) bus interface type select. The
functions of IOR, IOW, INT A-INTD, and CSA-CSD are re-assigned
with the logical state of this pin. When this pin is a logic 1, the 16
mode interface (16C554) is selected. When this pin is a logic 0, the
68 mode interface (68C554) is selected. When this pin is a logic 0,
IOW is re-assigned to R/W, RESET is re-assigned to RESET, IOR is
not used, and INTA-INTD are connected in a wire-OR conguration.
The wire-OR outputs are connected internally to the open drain IRQ
signal output. This pin is not available on 64-pin packages which
operate in the 16 mode only.
A0
34
24
48
I
Address 0 select bit. Internal registers address selection in 16 and
68 modes.
A1
33
23
47
I
Address 1 select bit. Internal registers address selection in 16 and
68 modes.
A2
32
22
46
I
Address 2 select bit. Internal registers address selection in 16 and
68 modes.
A3, A4
20, 50
-
I
Address 3-4 select bits. When the 68 mode is selected, these pins
are used to address or select individual UARTs (providing CS is a
logic 0). In the 16 mode, these pins are re-assigned as chip selects,
see CSB and CSC.
CDA, CDB,
CDC, CDD
9, 27,
43, 61
64, 18,
31, 49
19, 42,
59, 2
I
Carrier Detect (Active-LOW). These inputs are associated with
individual UART channels A through D. A logic 0 on this pin indicates
that a carrier has been detected by the modem for that channel.
CS
16
-
I
Chip Select (Active-LOW). In the 68 mode, this pin functions as a
multiple channel chip enable. In this case, all four UARTs (A-D) are
enabled when the CS pin is a logic 0. An individual UART channel is
selected by the data contents of address bits A3-A4. when the
16 mode is selected (68-pin devices), this pin functions as CSA (see
denition under CSA, CSB).
CSA, CSB,
CSC, CSD
16, 20,
50, 54
7, 11,
38, 42
28, 33,
68, 73
I
Chip Select A, B, C, D (Active-LOW). This function is associated
with the 16 mode only, and for individual channels ‘A’ through ‘D’.
When in 16 mode, these pins enable data transfers between the user
CPU and the SC16C554/554D for the channel(s) addressed.
Individual UART sections (A, B, C, D) are addressed by providing a
logic 0 on the respective CSA-CSD pin. When the 68 mode is
selected, the functions of these pins are re-assigned. 68 mode
functions are described under their respective name/pin headings.
CTSA, CTSB,
CTSC, CTSD
11, 25,
45, 59
2, 16,
33, 47
23, 38,
63, 78
I
Clear to Send (Active-LOW). These inputs are associated with
individual UART channels A through D. A logic 0 on the CTS pin
indicates the modem or data set is ready to accept transmit data from
the SC16C554/554D. Status can be tested by reading MSR[4]. This
pin only affects the transmit or receive operations when Auto CTS
function is enabled via the Enhanced Feature Register EFR[7] for
hardware ow control operation.
相關PDF資料 |
PDF描述 |
|---|---|
| V24C24H150B3 | CONVERTER MOD DC/DC 24V 150W |
| ATMEGA644V-10MUR | MCU AVR 64K FLASH 10MHZ 44QFN |
| SC28C94A1N,112 | IC UART QUAD W/FIFO 48-DIP |
| V24C24H150B | CONVERTER MOD DC/DC 24V 150W |
| SC16C554DIA68,512 | IC UART QUAD W/FIFO 68-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C554IB80 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C554IB80,528 | 功能描述:UART 接口集成電路 Quad UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554IB80,551 | 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554IB80,557 | 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
發布緊急采購，3分鐘左右您將得到回復。