參數資料
型號: SC16C554IB64,128
廠商: NXP Semiconductors
文件頁數: 20/55頁
文件大?。?/td> 0K
描述: IC UART QUAD SOT314-2
標準包裝: 1,500
通道數: 4,QUART
FIFO's: 16 字節
電源電壓: 2.5V,3.3V,5V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 64-LQFP
供應商設備封裝: 64-LQFP(10x10)
包裝: 帶卷 (TR)
其它名稱: 935270074128
SC16C554IB64-T
SC16C554IB64-T-ND
Philips Semiconductors
SC16C554/554D
Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 05 — 10 May 2004
27 of 55
9397 750 13132
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
7.4 Interrupt Status Register (ISR)
The SC16C554/554D provides six levels of prioritized interrupts to minimize external
software interaction. The Interrupt Status Register (ISR) provides the user with six
interrupt status bits. Performing a read cycle on the ISR will provide the user with the
highest pending interrupt level to be serviced. No other interrupts are acknowledged
until the pending interrupt is serviced. Whenever the interrupt status register is read,
the interrupt status is cleared. However, it should be noted that only the current
pending interrupt is cleared by the read. A lower level interrupt may be seen after
re-reading the interrupt status bits. Table 12 “Interrupt source” shows the data values
(bits 0-5) for the six prioritized interrupt levels and the interrupt sources associated
with each of these interrupt levels.
Table 12:
Interrupt source
Priority
level
ISR[5]
ISR[4]
ISR[3]
ISR[2]
ISR[1]
ISR[0]
Source of the interrupt
1
0
00110LSR (Receiver Line Status
Register)
2
0
00100
RXRDY (Received Data
Ready)
2
0
01100
RXRDY (Receive Data
time-out)
3
0
00010
TXRDY (Transmitter
Holding Register Empty)
4
0
00000
MSR (Modem Status
Register)
5
0
10000
RXRDY (Received Xoff
signal) / Special character
6
1
00000CTS, RTS change of state
Table 13:
Interrupt Status Register bits description
Bit
Symbol
Description
7:6
ISR[7:6]
FIFOs enabled. These bits are set to a logic 0 when the FIFO is
not being used. They are set to a logic 1 when the FIFOs are
enabled.
Logic 0 or cleared = default condition.
5:4
ISR[5:4]
INT priority bits 4-3. These bits are enabled when EFR[4] is set to
a logic 1. ISR[4] indicates that matching Xoff character(s) have
been detected. ISR[5] indicates that CTS, RTS have been
generated. Note that once set to a logic 1, the ISR[4] bit will stay a
logic 1 until Xon character(s) are received.
Logic 0 or cleared = default condition.
3:1
ISR[3:1]
INT priority bits 2-0. These bits indicate the source for a pending
interrupt at interrupt priority levels 1, 2, and 3 (see Table 12).
Logic 0 or cleared = default condition.
0
ISR[0]
INT status.
Logic 0 = An interrupt is pending and the ISR contents may be
used as a pointer to the appropriate interrupt service routine.
Logic 1 = No interrupt pending (normal default condition).
相關PDF資料
PDF描述
SC16C554IB64,151 IC UART QUAD SOT314-2
AT89C51RB2-RLRUL IC 8051 MCU 16K FLASH 44-VQFP
VI-B7N-IW-F2 CONVERTER MOD DC/DC 18.5V 100W
VI-B7N-IW-F1 CONVERTER MOD DC/DC 18.5V 100W
VI-B7M-IX-F4 CONVERTER MOD DC/DC 10V 75W
相關代理商/技術參數
參數描述
SC16C554IB80 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
SC16C554IB80,528 功能描述:UART 接口集成電路 Quad UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C554IB80,551 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C554IB80,557 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C650A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder