- 您現在的位置：買賣IC網 > PDF目錄372121 > SC16C554DB (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C554DB |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs |
| 中文描述： | 5伏，3.3伏和2.5伏兆5四異步/秒（最大），16字節的FIFO |
| 文件頁數： | 16/55頁 |
| 文件大?。?/td> | 276K |
| 代理商： | SC16C554DB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
Philips Semiconductors
SC16C554/554D
Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 05 — 10 May 2004
16 of 55
9397 750 13132
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
6.6 Hardware flow control
When automatic hardware flow control is enabled, the SC16C554/554D monitors the
CTS pin for a remote buffer overflow indication and controls the RTS pin for local
buffer overflows. Automatic hardware flow control is selected by setting EFR[6] (RTS)
and EFR[7] (CTS) to a logic 1. If CTS transitions from a logic 0 to a logic 1 indicating
a flow control request, ISR[5] will be set to a logic 1 (if enabled via IER[6,7]), and the
SC16C554/554D will suspend TX transmissions as soon as the stop bit of the
character in process is shifted out. Transmission is resumed after the CTS input
returns to a logic 0, indicating more data may be sent.
With the Auto RTS function enabled, an interrupt is generated when the receive FIFO
reaches the programmed trigger level. The RTS pin will not be forced to a logic 1
(RTS off), until the receive FIFO reaches the next trigger level. However, the RTS pin
will return to a logic 0 after the data buffer (FIFO) is unloaded to the next trigger level
below the programmed trigger. However, under the above described conditions, the
SC16C554/554D will continue to accept data until the receive FIFO is full.
6.7 Software flow control
When software flow control is enabled, the SC16C554/554D compares one or two
sequential receive data characters with the programmed Xon/Xoff or Xoff1,2
character value(s). If received character(s) match the programmed values, the
SC16C554/554D will halt transmission (TX) as soon as the current character(s) has
completed transmission. When a match occurs, the receive ready (if enabled via Xoff
IER[5]) flags will be set and the interrupt output pin (if receive interrupt is enabled) will
be activated. Following a suspension due to a match of the Xoff characters’ values,
the SC16C554/554D will monitor the receive data stream for a match to the Xon1,2
character value(s). If a match is found, the SC16C554/554D will resume operation
and clear the flags (ISR[4]).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to a logic 0.
Following reset, the user can write any Xon/Xoff value desired for software flow
control. Different conditions can be set to detect Xon/Xoff characters and
suspend/resume transmissions. When double 8-bit Xon/Xoff characters are selected,
the SC16C554/554D compares two consecutive receive characters with two software
flow control 8-bit values (Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions
accordingly. Under the above described flow control mechanisms, flow control
characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed,
the SC16C554/554D automatically sends an Xoff message (when enabled) via the
serial TX output to the remote modem. The SC16C554/554D sends the Xoff1,2
Table 6:
Selected trigger level
(characters)
1
4
8
14
Flow control mechanism
INT pin activation
Negate RTS or
send Xoff
4
8
12
14
Assert RTS or
send Xon
1
4
8
10
1
4
8
14
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C554DIA68 | Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C554DIB64 | Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C554IB80 | Quad UART with 16-byte FIFO and infrared (IrDA) encoder-decoder |
| SC16C650A | Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C650AIA44 | Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C554DBIA68 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554DBIA68,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554DBIA68,518 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554DBIA68,529 | 功能描述:UART 接口集成電路 4CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554DBIA68-T | 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。