<tfoot id="rcuf6"></tfoot>
<rt id="rcuf6"><form id="rcuf6"><small id="rcuf6"></small></form></rt>
  • <table id="rcuf6"><dl id="rcuf6"><sup id="rcuf6"></sup></dl></table>
  • <li id="rcuf6"></li>
  • 參數資料
    型號: SC16C554BIB64,157
    廠商: NXP Semiconductors
    文件頁數: 3/57頁
    文件大?。?/td> 0K
    描述: IC UART QUAD SOT314-2
    標準包裝: 800
    通道數: 4,QUART
    FIFO's: 16 字節
    電源電壓: 2.5V,3.3V,5V
    帶自動流量控制功能:
    帶故障啟動位檢測功能:
    帶調制解調器控制功能:
    帶CMOS:
    安裝類型: 表面貼裝
    封裝/外殼: 64-LQFP
    供應商設備封裝: 64-LQFP(10x10)
    包裝: 托盤
    其它名稱: 935274932157
    SC16C554BIB64
    SC16C554BIB64-ND
    SC16C554B_554DB
    All information provided in this document is subject to legal disclaimers.
    NXP B.V. 2010. All rights reserved.
    Product data sheet
    Rev. 4 — 8 June 2010
    11 of 58
    NXP Semiconductors
    SC16C554B/554DB
    5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
    CTSA
    11
    2
    23
    1
    I
    Clear to Send (active LOW). These inputs are
    associated with individual UART channels A to D. A
    logic 0 on the CTSn pin indicates the modem or data
    set is ready to accept transmit data from the
    SC16C554B/554DB. Status can be tested by reading
    MSR[4]. This pin only affects the transmit or receive
    operations when auto-CTS function is enabled via
    MCR[5] for hardware flow control operation.
    CTSB
    25
    16
    38
    12
    I
    CTSC
    45
    33
    63
    26
    I
    CTSD
    59
    47
    78
    -
    I
    D0
    66
    53
    7
    39
    I/O
    Data bus (bidirectional). These pins are the 8-bit,
    3-state data bus for transferring information to or from
    the controlling CPU. D0 is the least significant bit and
    the first data bit in a transmit or receive serial data
    stream.
    D1
    67
    54
    8
    40
    I/O
    D2
    68
    55
    9
    41
    I/O
    D3
    1
    56
    11
    42
    I/O
    D4
    2
    57
    12
    43
    I/O
    D5
    3
    58
    13
    44
    I/O
    D6
    4
    59
    14
    45
    I/O
    D7
    5
    60
    15
    46
    I/O
    DSRA
    10
    1
    22
    -
    I
    Data Set Ready (active LOW). These inputs are
    associated with individual UART channels, A through
    D. A logic 0 on this pin indicates the modem or data set
    is powered-on and is ready for data exchange with the
    UART. This pin has no effect on the UART’s transmit or
    receive operation.
    DSRB
    26
    17
    39
    -
    I
    DSRC
    44
    32
    62
    25
    I
    DSRD
    60
    48
    79
    -
    I
    DTRA
    12
    3
    24
    -
    O
    Data Terminal Ready (active LOW). These outputs
    are associated with individual UART channels, A
    through D. A logic 0 on this pin indicates that the
    SC16C554B/554DB is powered-on and ready. This pin
    can be controlled via the Modem Control Register.
    Writing a logic 1 to MCR[0] will set the DTRn output to
    logic 0, enabling the modem. This pin will be a logic 1
    after writing a logic 0 to MCR[0], or after a reset. This
    pin has no effect on the UART’s transmit or receive
    operation.
    DTRB
    24
    15
    37
    -
    O
    DTRC
    46
    34
    64
    27
    O
    DTRD
    58
    46
    77
    -
    O
    GND
    6, 23,
    40, 57
    14, 28,
    45, 61
    16, 36,
    56, 76
    21, 37,
    I
    Signal and power ground.
    INTA
    15
    6
    27
    4
    O
    Interrupt A, B, C, D (active HIGH). This function is
    associated with the 16 mode only. These pins provide
    individual channel interrupts INTA to INTD.
    INTA to INTD are enabled when MCR[3] is set to a
    logic 1, interrupts are enabled in the Interrupt Enable
    Register (IER), and when an interrupt condition exists.
    Interrupt conditions include: receiver errors, available
    receiver buffer data, transmit buffer empty, or when a
    modem status flag is detected. When the 68 mode is
    selected, the functions of these pins are re-assigned.
    68 mode functions are described under their respective
    name/pin headings.
    INTB
    21
    12
    34
    10
    O
    INTC
    49
    37
    67
    30
    O
    INTD
    55
    43
    74
    36
    O
    Table 2.
    Pin description …continued
    Symbol
    Pin
    Type
    Description
    PLCC68
    LQFP64
    LQFP80 HVQFN48
    相關PDF資料
    PDF描述
    VI-B6B-IY CONVERTER MOD DC/DC 95V 50W
    SCC2681AE1A44,518 IC DUART SOT187-2
    VI-B61-IY CONVERTER MOD DC/DC 12V 50W
    SCC2692AC1B44,557 IC UART DUAL W/FIFO 44PQFP
    SC16C554BIBM,157 IC UART QUAD SOT414-1
    相關代理商/技術參數
    參數描述
    SC16C554BIB64-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
    SC16C554BIB64-S 功能描述:UART 接口集成電路 4CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
    SC16C554BIB80 制造商:NXP Semiconductors 功能描述:IC UART QUAD 16BYTE FIFO 16C554 制造商:NXP Semiconductors 功能描述:IC, UART, QUAD, 16BYTE FIFO, 16C554 制造商:NXP Semiconductors 功能描述:IC, UART, QUAD, 16BYTE FIFO, 16C554; No. of Channels:4; Data Rate:5Mbps; Supply Voltage Min:2.25V; Supply Voltage Max:5.5V; Digital IC Case Style:LQFP; No. of Pins:80; Operating Temperature Min:-40C; Operating Temperature Max:85C; ;RoHS Compliant: Yes 制造商:NXP Semiconductors 功能描述:UART 4-CH 16Byte FIFO 2.5V/3.3V/5V 80-Pin LQFP T/R
    SC16C554BIB80,528 功能描述:UART 接口集成電路 4CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
    SC16C554BIB80,551 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel