參數資料
型號： SAK-XC164CS-8R20F
廠商： INFINEON TECHNOLOGIES AG
英文描述： 16-Bit Single-Chip Microcontroller
中文描述： 16位單片機
文件頁數： 42/71頁
文件大?。?/td> 2661K
代理商： SAK-XC164CS-8R20F
XC164
Derivatives
Functional Description
Data Sheet
38
V2.1, 2003-06
Summary of Features
CAN functionality according to CAN specification V2.0B active.
Data transfer rate up to 1 Mbit/s
Flexible and powerful message transfer control and error handling capabilities
Full-CAN functionality and Basic CAN functionality for each message object
32 flexible message objects
– Assignment to one of the two CAN nodes
– Configuration as transmit object or receive object
– Concatenation to a 2-, 4-, 8-, 16-, or 32-message buffer with FIFO algorithm
– Handling of frames with 11-bit or 29-bit identifiers
– Individual programmable acceptance mask register for filtering for each object
– Monitoring via a frame counter
– Configuration for Remote Monitoring Mode
Up to eight individually programmable interrupt nodes can be used
CAN Analyzer Mode for bus monitoring is implemented
Note: When a CAN node has the interface lines assigned to Port 4, the segment address
output on Port 4 must be limited. CS lines can be used to increase the total amount
of addressable external memory.
3.14
Watchdog Timer
The Watchdog Timer represents one of the fail-safe mechanisms which have been
implemented to prevent the controller from malfunctioning for longer periods of time.
The Watchdog Timer is always enabled after a reset of the chip, and can be disabled
until the EINIT instruction has been executed (compatible mode), or it can be disabled
and enabled at any time by executing instructions DISWDT and ENWDT (enhanced
mode). Thus, the chip’s start-up procedure is always monitored. The software has to be
designed to restart the Watchdog Timer before it overflows. If, due to hardware or
software related failures, the software fails to do so, the Watchdog Timer overflows and
generates an internal hardware reset and pulls the RSTOUT pin low in order to allow
external hardware components to be reset.
The Watchdog Timer is a 16-bit timer, clocked with the system clock divided by 2/4/128/
256. The high byte of the Watchdog Timer register can be set to a prespecified reload
value (stored in WDTREL) in order to allow further variation of the monitored time
interval. Each time it is serviced by the application software, the high byte of the
Watchdog Timer is reloaded and the low byte is cleared. Thus, time intervals between
13
μ
s and 419 ms can be monitored (@ 40 MHz).
The default Watchdog Timer interval after reset is 3.28 ms (@ 40 MHz).
相關PDF資料
PDF描述
SAK-XC164CS-8R40F 16-Bit Single-Chip Microcontroller
SAK-XC164CS-16F20F 16-Bit Single-Chip Microcontroller
SAK-XC164CS-16F40F 16-Bit Single-Chip Microcontroller
SAF-XC164CS-16F40F 16-Bit Single-Chip Microcontroller
SAK-XC164CS-16R20F 16-Bit Single-Chip Microcontroller
相關代理商/技術參數
參數描述
SAK-XC164CS-8R40F 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller
SAK-XC167CI-16F20F 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bi t Single-Chip Microcontroller Preliminary
SAK-XC167CI-16F20F BB 功能描述:16位微控制器 - MCU MICROCONTROLLER 16-BIT RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
SAK-XC167CI-16F40F 制造商:Infineon Technologies AG 功能描述:
SAK-XC167CI-16F40F BB 功能描述:16位微控制器 - MCU 16 BIT SNGL CHIP 5V 40MHz Flash RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*