參數資料
型號: SAI06
廠商: SANKEN ELECTRIC CO LTD
元件分類: 穩壓器
英文描述: 9V,Surface Mount Switching Regulator IC(9v,表貼開關穩壓器芯片)
中文描述: 0.45 A SWITCHING REGULATOR, 60 kHz SWITCHING FREQ-MAX, PDSO4
封裝: PLASTIC, SMT-4
文件頁數: 3/4頁
文件大?。?/td> 66K
代理商: SAI06
66
I
Selecting External Components
1. Inductor L
1
1) It must be suited for switching regulators.
Do not use inductors such as noise filters, because they generate excessive heat.
2) It must have the appropriate inductance value.
If the inductance is too small (150
μ
H or lower), abnormal oscillation may occur causing operation problems in the overcurrent protection
circuit within the rated current range.
3) The rated current must be satisfied.
If the rated current is exceeded, magnetic saturation leads to overcurrent.
2. Capacitors C
1
and C
2
1) They must satisfy the breakdown voltage and allowable ripple current.
Exceeding the ratings of these capacitors or using them without derating shortens their service lives and may also cause abnormal
oscillation of the IC.
2) C
2
should be a low-impedance type capacitor.
A low-impedance type capacitor is recommended for C
2
to ensure reduced ripple voltage and stable switching operation.
3. Diode D
1
The Sanken SFPB54 diode is recommended for D
1
. If you intended to use an equivalent diode, be sure to use a Schottky Barrier diode and
make sure that the reverse voltage applied to terminal 2 of the IC does not exceed the value (
1V) given in the absolute maximum ratings. If
you use a fast recovery diode or any other diode, supplying a reverse voltage generated from the recovery or ON voltage of the diode may
damage the IC.
Application
Variable output voltage
Output voltage can be adjusted in the same way as SI-8000S in page 77.
I
Example of Printed Circuit Board
a) For optimum operation, there must be only
one GND line originating from terminal 4
and each component must be connected
with the shortest possible wiring.
b) To prevent heating of the IC, it is best to
make the GND pattern as large as pos-
sible since the internal frame and termi-
nal 4 (GND) are connected to each other.
I
T
a
-P
D
Characteristics
The efficiency depends on the input voltage and the out-
put current. Thus, obtain the value from the efficiency
graph on page 67 and substitute the percentage in the
formula above.
V
O
:Output voltage
I
O
:Output current
η
x:Efficiency (%)
V
F
:Diode forward voltage
SFPB54-0.3V
Thermal design for D
1
must be considered separately.
+
+
V
IN
DI
1
C
1
L
1
C
2
GND
SW
V
O
1
2
3
4
SAI
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
30
0
Ambient Temperature T
a
(
°
C)
25
50
75
100
125
P
D
Glass epoxy
substrate
(95
×
69
×
1.2)
No airflow
G
SAI Series
P
D
=V
O
I
O
100
1
V
F
I
O
1
V
O
ηχ
V
IN
相關PDF資料
PDF描述
SAP08N Darlington Transistors With Built-in Temperature Compensation Diodes for Audio Amplifier Applications(內置溫度補償二極管的達林頓晶體管(用于音頻放大器))
SAP10 Darlington transistors with built-in temperature compensation diodes for audio amplifier applications
SAP15 Darlington transistors with built-in temperature compensation diodes for audio amplifier applications
SAP10N Darlington Transistors With Built-in Temperature Compensation Diodes for Audio Amplifier Applications(內置溫度補償二極管的達林頓晶體管(用于音頻放大器))
SAP10P Darlington Transistors With Built-in Temperature Compensation Diodes for Audio Amplifier Applications(內置溫度補償二極管的達林頓晶體管(用于音頻放大器))
相關代理商/技術參數
參數描述
SAI100A 制造商:ESSENTRA COMPONENTS 功能描述:SQUARE ADJUSTABLE INSERT:NYL BLA 制造商:Richco 功能描述:SQUARE ADJUSTABLE INSERT:NYL BLA
SAI-1011 制造商:MICRO-ELECTRONICS 制造商全稱:Micro Electronics 功能描述:COMMON MODE CHOKE FOR ADSL MODEM
SAI13AG 制造商:Rochester Electronics LLC 功能描述:- Bulk
SAI200A 制造商:Richco 功能描述:SQUARE ADJUSTABLE INSERT:NYL BLA
SAI300A 制造商:Richco 功能描述:SQUARE ADJUSTABLE INSERT:NYL BLA